Festo DGC G Series Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 136

background image

27 / 44

Festo 7DGC-KFa_en

Adjust the excess sealing band and cover band by moving the piston back

•

and forth and pulling or pushing the respective bands at the same time so
that the excess band is no greater than the width of the contact surface (X)
on the buffer (see table).

Type

Width of the contact surface X

DGC-18-…-KF

6 mm

DGC-25-…-KF

7 mm

DGC-32-…-KF

9 mm

DGC-40-…-KF

9 mm

Grease the buffer.

•

Observe the greasing instructions in the table at the start of this chapter.
Insert the buffer into the cylinder barrel.

•

Note

When using shock absorbers on the end caps the regulating screw for the
end position cushioning (see chapter 3.2 and 3.3, entry 11) must be “open”.

Unscrew it far enough so that it is positioned flush with the buffer.

Grease the sealing ring and insert it into the buffer.

•

Note

The sealing band and cover band must not protrude beyond the buffers,
otherwise the end cap cannot form an air-tight seal and may have an adverse
effect on the function of the linear drive. The sealing band and cover band

have to be shortened so that they seal off flush with the outer edge of the

buffers. However, it is better if they are slightly short of the buffers.

Apply the band clamping mechanism to the sealing band and cover band.

•

Apply Loctite 243 to the socket head screw and tighten it using the appro-

•

priate torque (see table).

Type

Torque

DGC-18-…-KF

0.2 Nm ±10%

DGC-25-…-KF

0.4 Nm ±10%

DGC-32-…-KF

0.4 Nm ±10%

DGC-40-…-KF

1.0 Nm ±10%

Move the piston to the other end of the cylinder barrel once in order to

•

secure the sealing band back in the slot.

X

«
...
117
118
119
120
121
...
»

Содержание DGC G Series









































































































































Отзывы:

Нет отзывов

Похожие инструкции для DGC G Series

Бренд: Teac Страницы: 74

Ultrastar DC ME200

Бренд: Western Digital Страницы: 45

Бренд: Fastech Страницы: 26

Бренд: Johnson Controls Страницы: 4

Бренд: Toshiba Страницы: 18

EZN3B0055H060N003

Бренд: Lenze Страницы: 46

Бренд: Lenze Страницы: 63

Бренд: Lenze Страницы: 250

Бренд: STG-BEIKIRCH Страницы: 25

Бренд: Shugart Страницы: 32

Бренд: Lenze Страницы: 189

EtherCAT EHS-580

Бренд: Econ Страницы: 36

SGD7S-****20A Series

Бренд: YASKAWA Страницы: 561

Бренд: Grundfos Страницы: 24

Opal Pro MS6 Series

Бренд: SAF Страницы: 38

SGD7C-***AMAA***

Бренд: YASKAWA Страницы: 669

VLT 2800 Series

Бренд: Danfoss Страницы: 103

Бренд: Lenze Страницы: 199

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды