background image

Not for 

Reproduction

42

www.ferrismowers.com

• If the measurements are greater than 4" (10,2 cm)

loosen the jam nut (D, Figure 55) and turn the fine

adjustment nut (E) 

counter-clockwise

 to lower the

deck.

• If the measurements are less than 4" (10,2 cm)

loosen the jam nut and turn the fine adjustment bolt

clockwise

 to raise the deck.

8. Once the 4" measurement from the front tip of the blade

is achieved, tighten the jam nut.

9. Loosen the nuts (F) that secure the rear hanger chain (G)

to the rear mounting plate (H) and allow the rear of the

deck to rest on the 2 X 4's and 1/4" (0,64 cm) spacers.

10. Repeat steps #7 - #9 for the other side of the unit.
11. Remove all blocking from beneath the mower deck.
12. Perform the 

Determining if the Deck Leveling Needs to

be Adjusted

 procedure to verify that the deck has been

leveled correctly.

Deck Lift Assist Springs

Some models are equipped with deck lift assist springs (A,

Figure 57) that assist the operator in raising the mower deck

with the deck lift pedal. The deck lift assist springs are factory

set to provide optimal lifting performance.

57

Although it is fastened with a multi-position anchor, this is 

not

an adjustment point

.

Do NOT attempt to adjust the spring length or lifting

performance will be compromised.

Long Left Hand Deck Belt Replacement

NOTICE

To avoid damaging belts, 

do not pry over

pulleys

.

1. Park the unit on a smooth level surface such as a

concrete floor. Disengage the PTO, engage the parking

brake, turn the ignition switch to OFF, and remove the

ignition key.

2. Lower the mower deck to it’s lowest cutting position and

remove the mower deck guards and floor pan to gain

access to the mower deck drive belts.

 WARNING

Use extreme caution when rotating the idler arm with the

breaker bar, due to the increased tension in the spring

as the idler arm is being rotated. Injury may result if the

breaker bar is prematurely released while the spring is

under tension.

3. Using a 1/2" breaker bar (A, Figure 58) place the square

end in the opening in the PTO clutch drive idler arm (B)

and rotate the idler arm 

clockwise

, which will relieve

tension on the belt exerted from the idler arm. Remove

the belt from the left hand side spindle pulley (C).

Carefully release the tension on the breaker bar.

58

4. Remove the long left hand belt (D) from the adjustable

idler pulley (E) and it’s belt guide (F).

5. Remove the old long left hand belt from the PTO clutch

pulley (G) and the top groove of the center spindle pulley

(H).

6. Install the new long left hand belt onto the PTO clutch

pulley and the center spindle pulley.

7. Install the long left hand belt into the belt guide on the

adjustable idler pulley.

8. Verify that the V-side of the belt runs in the pulley grooves

of the center spindle pulley and the PTO clutch pulley.

Make sure that the back side of the belt contacts the face

of the adjustable idler pulley. Make sure that the belt is

correctly routed in the belt guides (F & I).

9. Using a 1/2" breaker bar place the square end in the

opening in the PTO clutch drive idler arm and rotate the

idler arm 

clockwise

, which will relieve tension on the belt

exerted from the idler arm. Install the long left hand belt

onto the left hand spindle pulley. Carefully release the

tension on the breaker bar.

10. Measure the coil-to-coil length (A, Figure 59) of the long

left hand belt tensioning spring (B). The measurement

should equal 10-1/4” (26 cm) ± 1/8 (0,32 cm). If not,

Содержание 5901879

























































Отзывы: