Ferris 5901879 Скачать руководство пользователя страница 15

Страница: 15 / 56

Not for

Reproduction

Danger - Thrown objects hazard:

Keep bystanders and children a

safe distance away. Remove objects

that can be thrown by the blade. Do

not mow without discharge chute in

place.

*This limit was determined per International Standard ISO 5395-3:2013,

Section 4.6 and is based on the ISO 5395-3 Stability Test procedure

described in Annex A. The 15 degree “limit of stability” is equal to 60%

of the angle at which machine lift-off occurred in static tests. Actual

dynamic stability may vary depending on operating conditions.

7106109 - Decal, Danger, Discharge

Danger - Thrown Objects Hazard:

Do not mow without discharge chute or

entire grass catcher in place.

Danger - Amputation and Thrown

Objects Hazard:

To avoid injury from

rotating blades, stay clear of deck edge

and keep others away.

5061246 - Decal, Pinch Point

Danger: Dismemberment

- This machine

can crush and cut. Keep hands away from

deck lift rod.

5061042 - Decal, Danger

Danger: Dismemberment:

This machine

can crush and cut. Keep hands away from

belts and pulleys.

5102456 - Decal, Fire

Danger: Fire Hazard:

Keep unit free of

grass, leaves and excess oil. Do not add fuel

while engine is hot or running. Stop engine,

remove key and allow to cool for at least 3

minutes prior to adding fuel. Do not add fuel

indoors, in an enclosed trailer, garage or

other enclosed areas. Clean up spilled fuel.

Do not smoke while operating this machine.

Battery Safety Decal

Warning: Fire Hazard

- Keep children,

open flames and sparks away from the

battery, which could ignite explosive gases.

Warning: Sulfuric acid can cause

blindness or severe burns

- Always

wear safety goggles or a face shield when

working on or near a battery.

Warning: Batteries produce explosive

gases

- Read and understand the

Operator’s Manual before using this

machine.

Important: Do not discard a battery in the

trash

- Contact local authorities for disposal

and/or recycling of batteries.

Flush eyes immediately with water. Get

medical help fast.

Содержание 5901879

























































Результаты поиска

Содержание 5901879

Отзывы:

Похожие инструкции для 5901879

Бренды по названию

Популярные бренды

Ferris 5901879, Руководство оператора

Результаты поиска

Содержание 5901879

Отзывы:

Похожие инструкции для 5901879

Бренды по названию

Популярные бренды