Ferris 5901879 Скачать руководство пользователя страница 35

Страница: 35 / 56

Not for

Reproduction

7. The mower blade should have a maximum of 1/64" (0,40

mm) cutting edge (B) or less.

CAUTION

Thrown objects hazard.

An unbalanced mower blade can create excessive vibration

and damage the unit, or cause mower blade failure resulting

in thrown debris.
Be sure blade is balanced before installing.

8. Clamp a nail in a bench vise, hang the blade on the nail,

and position the blade in a level horizontal position as

shown in Figure 39.

9. Check the balance of the blade. If either end of the

blade moves downward the end that moves downward

is heavier than the other. Sharpen the heavy end until

balance is achieved.

10. Repeat the process until the mower blade remains in the

horizontal, level position.

Installing the Mower Blades

CAUTION

Laceration hazard.

Mower blades are sharp.
Always wear gloves when handling, or working near, mower

blades.

1. Install each mower blade with the air lifts (C, Figure 40)

pointing up towards the mower deck as shown in Figure

40 and secure with the mower blade mounting bolt (A)

and flat washer (B).

2. Wedge a wooden block (D) between the mower blade

and the mower deck housing to keep the mower blade

from turning and torque the blade mounting bolt to 120 ft.

lbs (163 Nm).

Seat Adjustment (Suspension Seat)

This procedure only applies to models equipped with a

suspension seat.
In addition to the forwards and backwards seat adjustment,

models equipped with a suspension seat can also be

adjusted for suspension (ride comfort).

Seat Adjustment Lever (Forwards/Backwards):

The

seat can be adjusted forward and back. Move the forwards/

backwards seat adjustment lever (A, Figure 41), position

the seat as desired, and release the lever to lock the seat in

position. Suspension Seat Adjustment

Содержание 5901879

























































Результаты поиска

Содержание 5901879

Отзывы:

Похожие инструкции для 5901879

Бренды по названию

Популярные бренды

Ferris 5901879, Руководство оператора

Результаты поиска

Содержание 5901879

Отзывы:

Похожие инструкции для 5901879

Бренды по названию

Популярные бренды