Ferris 5901879 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 56

background image

Not for

Reproduction

23

Reverse Travel Practice

15

LOOK DOWN AND BEHIND, then gradually move both

ground speed control levers evenly BACK from neutral. Slow

down and repeat.

Note:

Practice backing up for several minutes before

attempting to do so near objects. The zero-turn riding mower

turns sharply in reverse as well as forward, and backing up

straight takes practice.

Practice Turning Around A Corner

16

While traveling forward allow one ground speed control lever

to gradually return back toward neutral. Repeat several times.

Note:

To prevent pivoting directly on the tire tread, it is best to

keep both wheels going at least slightly forward.

Practice Turning in Place

17

To turn in place, “zero-turn,” gradually move one ground

speed control lever forward from neutral and the other lever

back from neutral simultaneously. Repeat several times.

Note:

Changing the amount each ground speed control lever

is pulled—forward or back, changes the “pivot point” you turn

on.

Advanced Driving

Executing an End-Of-Row Zero-Turn

18

Your zero-turn riding mower's unique ability to turn in place

allows you to turn around at the end of a cutting row rather

than having to stop and Y-turn before starting a new row.
For example, to execute a left end-of row zero turn:

1. Slow down at the end of the row.
2. Move the RIGHT ground speed control lever forward

slightly while moving the LEFT ground speed control lever

back to center and then slightly back from center.

3. Begin mowing forward again.
This technique turns the unit LEFT and slightly overlaps the

row just cut — eliminating the need to back up and re-cut

missed grass.

«
...
21
22
23
24
25
...
»

Содержание 5901879

























































Отзывы:

Нет отзывов

Похожие инструкции для 5901879

Бренд: Texas Страницы: 28

Бренд: SANLI Страницы: 16

Бренд: Viking Страницы: 36

Бренд: Toro Страницы: 80

Бренд: Nakayama Страницы: 14

Бренд: Garland Страницы: 64

Бренд: Bolens Страницы: 32

Бренд: Toro Страницы: 60

Бренд: RHINO Страницы: 160

Бренд: VITO GARDEN Страницы: 64

Бренд: Murray Страницы: 142

Бренд: Murray Страницы: 52

Бренд: Murray Страницы: 72

Бренд: Husqvarna Страницы: 11

Бренд: Husqvarna Страницы: 24

Бренд: Husqvarna Страницы: 24

Бренд: Husqvarna Страницы: 40

PZ5426FX / 966614001

Бренд: Husqvarna Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды