Ferris 5901879 Скачать руководство пользователя страница 48

Страница: 48 / 56

Not for

Reproduction

www.ferrismowers.com

Problem: Engine will not turnover or start.

Fuel Injected Models:

Malfunction

in fuel injection system.

See authorized service dealer.

Problem: Engine starts hard or runs poorly.

Cause

Remedy

Fuel mixture too rich.

1.) Clean air filter. 2.)

Carburated

Models:

Check choke adjustment.

Fuel Injected Models:

See

authorized dealer.

Spark plug(s) faulty, fouled or

incorrectly gapped.

Clean and gap or replace. See

engine manual.

Problem: Engine knocks.

Cause

Remedy

Low oil level.

Check / Add oil as required.

Using wrong grade oil.

See engine manual.

Problem: Excessive oil consumption.

Cause

Remedy

Engine running too hot.

Clean engine fins, blower screen,

and air cleaner.

Using wrong weight oil.

See engine manual.

Too much oil in crankcase.

Drain excess oil

Problem: Engine exhaust is black.

Cause

Remedy

Dirty air filter.

Replace air filter. See engine

manual.

Carbureted Models:

Engine choke

control is in closed position.

Move choke control to open position.

Problem: Malfunction Indicator Lamp (M.I.L.)

is flashing (Fuel Injected Models only).

Cause

Remedy

Problem with the fuel injection

system.

See your authorized service dealer.

Problem: Engine runs but mower will not drive.

Cause

Remedy

Transmissions are not engaged.

Engage the transmissions. See

Pushing the Rider by Hand

Belt is broken.

See

Transmission Drive Belt

Replacement

Drive belt slips.

See problem and cause below.

Brake is not fully released.

See authorized service dealer.

Problem: Unit drive belt slips.

Cause

Remedy

Pulleys or belt greasy or oily.

Clean as required.

Tension too loose

Adjust spring tension. See

Transmission Drive Belt

Replacement

Belt stretched or worn

Replace belt.

Problem: Brake will not hold.

Cause

Remedy

Brake is incorrectly adjusted.

See

Parking Brake Adjustment

Braking pads in transmissions worn. See authorized dealer.

Problem: Unit steers or handles poorly.

Cause

Remedy

Steering linkage is loose.

Check and tighten any loose

connections.

Improper tire inflation

See

Checking Tire Pressures

Troubleshooting the Mower

Problem: Mower will not raise.

Cause

Remedy

Lift linkage not properly attached or

damaged.

See authorized dealer.

Problem: Engine stalls easily with mower engaged.

Cause

Remedy

Engine speed to slow.

Set to full throttle.

Ground speed too fast.

Decrease ground speed.

Cutting height set too low.

Increase the cutting height.

Discharge chute jamming with cut

grass.

Cut grass with discharge pointing

towards previously cut area.

Problem: Excessive mower vibration.

Cause

Remedy

Blade mounting bolts are loose.

Tighten to 120 ft.lbs (163 Nm).

Mower blades, arbors, or pulleys are

bent.

Check and replace as necessary.

Mower blades are out of balance.

Remove, sharpen, and balance

blades. See

Servicing the Mower

Blades

Belt installed incorrectly.

Reinstall belt correctly.

Problem: Excessive belt wear or breakage.

Cause

Remedy

Bent or rough pulleys.

Repair or replace.

Using incorrect belt.

Replace with correct belt.

Incorrect belt tension.

Adjust to correct tension.

Problem: Drive belt slips or fails to drive.

Cause

Remedy

Incorrect belt tension.

Adjust to correct tension.

Drive belt is broken.

Replace with new belt.

Problem: Mower does not engage.

Cause

Remedy

Electrical wiring damage.

Locate & repair damaged wire.

Battery voltage too low.

Recharge battery and check

alternator. See

Battery Service

Troubleshooting Common Cutting

Problems

Problem: Streaking

Streaking is when thin strips of uncut grass are left behind the mower.

Streaking is usually caused by operator error or poor blade maintenance.

Содержание 5901879

























































Результаты поиска

Содержание 5901879

Отзывы:

Похожие инструкции для 5901879

Бренды по названию

Популярные бренды

Ferris 5901879, Руководство оператора

Результаты поиска

Содержание 5901879

Отзывы:

Похожие инструкции для 5901879

Бренды по названию

Популярные бренды