Ferris 5900576 Скачать руководство пользователя страница 42

Страница: 42 / 52

www.ferrisindustries.com

Regular Maintenance

Check the Mower Belt Idler Tensioner Spring
Length

1. Park the machine on a smooth level surface such

as a concrete floor. Disengage the PTO, engage
the parking brake, turn off the engine and remove
the ignition key.

2. Lower the mower deck to its lowest cutting

position.

3. Use the Mower Belt Idler Spring Length Chart to

determine the correct spring length.

4. Measure the coil length of the mower belt tension

spring (A, Figure 45). The measurement should
equal the measurement as designated in the
chart. If the measurement does not equal the
measurement as designated in the chart, adjust
the anchor eyebolt (B).

Adjusting the Mower Belt Idler Spring Length

1. Loosen the jam nut (C, Figure 45).
2. Turn the adjustment nut (D) until the measurement

as designated in the chart is achieved.

3. Retighten the jam nut.

Figure 45. Mower Belt Idler Spring Length
A. Mower Belt Tensioner Spring
B. Anchor Eyebolt
C. Jam Nut
D. Adjustment Nut
E. Measurement

Mower Belt Idler Spring Length

Deck Size

Measurement

inch

48”

6-3/4”

17,1

52”

7”

17,8

Not

for

Reproduction

Содержание 5900576





















































Результаты поиска

Содержание 5900576

Отзывы:

Похожие инструкции для 5900576

Бренды по названию

Популярные бренды

Ferris 5900576, Руководство оператора

Результаты поиска

Содержание 5900576

Отзывы:

Похожие инструкции для 5900576

Бренды по названию

Популярные бренды