Ferris 5900576 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 52

background image

5

Operator Safety

Enclosed Areas

Only operate this unit outdoors and
away from unventilated areas such as
inside garages or enclosed trailers.
The engine emits poisonous carbon
monoxide gas and prolonged exposure
in an enclosed area can result in
serious injury or death.

Fuel and Maintenance

Always disengage all drives, shutoff the engine, and
remove the key before doing any cleaning, refueling, or
servicing.

Gasoline and its vapors are extremely flammable. Do not
smoke while operating or refueling. Do not add fuel while
engine is hot or running. Allow engine to cool for at least
3 minutes prior to adding fuel.

Do not add fuel indoors, in an enclosed trailer, garage,
or any other enclosed area that is not well ventilated.
Gasoline spills should be cleaned up promptly and before
operation begins.

Gasoline should be stored only in sealed containers
approved for fuel.

Proper maintenance is critical to the safety and
performance of your unit. Keep the unit free of
grass, leaves, and excess oil. Be sure to perform the
maintenance procedures listed in this manual, especially
periodically testing the safety system.

Not

for

Reproduction

«
...
5
6
7
8
9
...
»

Содержание 5900576





















































Отзывы:

Нет отзывов

Похожие инструкции для 5900576

Бренд: Gardena Страницы: 9

Бренд: Parklander Страницы: 42

Бренд: Atom Страницы: 6

Бренд: TOPMAQ Страницы: 20

Бренд: Sabo Страницы: 92

Бренд: Parkside Страницы: 50

Бренд: SaMASZ Страницы: 36

Бренд: COMPANION Страницы: 76

Бренд: Lastec Страницы: 68

Бренд: Bad Boy Страницы: 34

LX466 13AT61RH044

Бренд: Toro Страницы: 36

Бренд: Wards Garden Mark Страницы: 12

CRAFTSMAN 944.604060

Бренд: Sears Страницы: 56

Бренд: GGP ITALY Страницы: 176

Бренд: Ryobi Страницы: 13

Бренд: Ryobi Страницы: 48

Бренд: Ryobi Страницы: 24

Бренд: Ryobi Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды