Ferris 5900576 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 52

background image

13

Control Functions

The information below briefly describes the function of individual controls. Starting, stopping, driving, and
mowing require the combined use of several controls applied in specific sequences. To learn what combination
and sequence of controls to use for various tasks see the OPERATION section.

Ground Speed Levers

These levers control the ground speed of the rider.
The left lever controls the left rear drive wheel and
the right lever controls the right rear drive wheel.

Moving a lever forward increases the FORWARD
speed of the associated wheel, and pulling back on a
lever increases the REVERSE speed.

Note: The further a lever is moved away from the
neutral position the faster the drive wheel will turn.

See the Operating the Zero Turn Rider section for
steering instructions.

Seat Adjustment Lever

The seat can be adjusted forward and back. Move the
lever towards the left, position the seat as desired,
and release the lever to lock the seat in position.

Ignition Switch

The ignition switch starts and stops the engine, it has
three positions:

OFF

Stops the engine and shuts off the

electrical

system.

RUN

Allows the engine to run and powers

the electrical system.

START Cranks the engine for starting.

NOTE: Never leave the ignition switch in the RUN
position with the engine stopped–this drains the

battery.

Figure 1. Control Locations

Features and Controls

Features & Controls

Not

for

Reproduction

«
...
13
14
15
16
17
...
»

Содержание 5900576





















































Отзывы:

Нет отзывов

Похожие инструкции для 5900576

Бренд: Gardena Страницы: 56

Бренд: Gardena Страницы: 4

Бренд: McCulloch Страницы: 20

Electrolux Power Compact

Бренд: Flymo Страницы: 9

Бренд: Ryobi Страницы: 16

Бренд: Nakayama Страницы: 65

Бренд: Weed Eater Страницы: 48

GLM 40/140 P EASY

Бренд: F.F. Group Страницы: 96

Бренд: Wizard Страницы: 48

Бренд: Gardeo Страницы: 128

Бренд: S.E.P. Страницы: 20

Бренд: Snapper Страницы: 52

Yanmar 59A40009727

Бренд: Cub Cadet Страницы: 24

Бренд: ARNETOLI MOTOR Страницы: 2

Бренд: Makita Страницы: 252

Бренд: Makita Страницы: 32

Бренд: Makita Страницы: 72

Бренд: Makita Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды