Ferris 5900576 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 52

background image

WARNING

Engine exhaust from this product contains
chemicals known by the State of California to
cause cancer, birth defects, or other reproductive
harm.

Thank you

for purchasing this quality-built Ferris product. We’re pleased that you’ve placed your confidence in the

Ferris brand. When operated and maintained according to the instructions in this manual, your Ferris product will
provide many years of dependable service.

This manual contains

safety information to make you aware of the hazards and risks associated with this machine

and how to avoid them. This machine is designed and intended to be used and maintained according to the manual
and operated by trained professionals for finish cutting of established lawns and is not intended for any other
purpose. It is important that you read and understand these instructions thoroughly before attempting to start or
operate this equipment

Briggs & Stratton Power Products Group, LLC.
Copyright © 2011 Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.

The Ferris logo is a trademark of Briggs & Stratton
Corporation Milwaukee, WI, USA.

Contact Information:

Briggs & Stratton Power Products Group, LLC

5375 N. Main St.
Munnsville, NY 13409-4003
(800) 933-6175
www.ferrisindustries.com

WARNING

Battery posts, terminals, and related accessories
contain lead and lead compounds — chemicals
known to the State of California to cause cancer
and reproductive harm.
Wash hands after handling.

PRODUCT REFERENCE DATA

Unit Model Number

Unit SERIAL Number

Mower Deck Model Number

Mower Deck SERIAL Number

Dealer Name

Date Purchased

ENGINE REFERENCE DATA

Engine Make

Engine Model

Engine Type/Spec.

Engine Code/Serial Number

SAMPLE

SAMPLE

When contacting your authorized dealer for
replacement parts, service, or information you
MUST have these numbers.

Record your part number, serial number and engine
serial numbers in the space provided for easy access.
These numbers can be found in the locations shown.

NOTE: For location of engine identification numbers,
refer to the engine owner’s manual.

Identification

Tag

USA Models

Identification Numbers

Not

for

Reproduction

«
1
2
3
4
...
»

Содержание 5900576





















































Отзывы:

Нет отзывов

Похожие инструкции для 5900576

Бренд: Yard Machines Страницы: 20

Бренд: Yard-Man Страницы: 32

Бренд: Yard Machines Страницы: 32

YP21KH42 (96041031300)

Бренд: Yard Pro Страницы: 20

Бренд: Yard-Man Страницы: 24

Бренд: Rally Страницы: 19

Бренд: Toro Страницы: 52

Бренд: Yard Works Страницы: 35

Powermaster 11029S

Бренд: Rover Страницы: 1

Бренд: Yazoo/Kees Страницы: 19

Бренд: Hyundai Страницы: 46

Бренд: Partner Страницы: 10

Бренд: Columbia Страницы: 41

Бренд: Cub Cadet Страницы: 2

Efco DR 55 H 6,5

Бренд: EMAK Страницы: 156

Бренд: Honda Страницы: 24

Бренд: Honda Страницы: 24

Бренд: Honda Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды