Ferris 5900576 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 52

background image

15

General Operating Safety

Before first time operation:

• Be sure to read all information in the Safety and

Operation sections before attempting to operate
this tractor and mower.

• Become familiar with all of the controls and how to

stop the unit.

• Drive in an open area without mowing to become

accustomed to the unit.

Checks Before Starting

• Check that crankcase is filled to full mark on

dipstick. See the engine Operator’s Manual for
instructions and oil recommendations.

• Make sure all nuts, bolts, screws and pins are in

place and tight.

• Adjust the seat position, and make certain you can

reach all controls from operator’s position.

• Fill the fuel tank with fresh fuel. Refer to engine

manual for fuel recommendations.

WARNING

Never allow passengers to ride on the unit.

Before leaving the operator’s position for any
reason, engage the parking brake, disengage
the PTO, stop the engine and remove the key.

To reduce fire hazard, keep the engine, tractor
and mower free of grass, leaves and excess
grease. Do not stop or park tractor over dry
leaves, grass or combustible materials.

Gasoline is highly flammable and must be
handled with care. Never fill the tank when the
engine is still hot from recent operation. Do not
allow open flame, smoking or matches in the
area. Avoid over-filling and wipe up any spills.

Do not load this zero-turn rider on a trailer or
truck using two separate ramps. Only use
a single ramp that is at least one foot wider
than the width of the rear wheels of this rider.
This rider has a zero turning radius and the
rear wheels could fall off the ramps, or the
rider could tip over injuring the operator or
bystanders.

WARNING

Never operate on slopes greater than 15°.

Select slow ground speed before driving onto
a slope. Use extra caution when operating on
slopes with a rear-mounted grass catcher.

Mow across the face of slopes, not up and
down, use caution when changing directions
and DO NOT START OR STOP ON SLOPE.

WARNING

Operation

Not

for

Reproduction

«
...
15
16
17
18
19
...
»

Содержание 5900576





















































Отзывы:

Нет отзывов

Похожие инструкции для 5900576

Бренд: Sabo Страницы: 56

Бренд: Lastec Страницы: 69

Бренд: LawnBoss Страницы: 34

Бренд: Yard Machines Страницы: 20

Бренд: Pattfield Ergo Tools Страницы: 80

Cheetah SCZ48V-22FX

Бренд: Scag Power Equipment Страницы: 78

Бренд: Jacobsen Страницы: 152

Бренд: Snapper Страницы: 28

Бренд: Ryobi Страницы: 20

Бренд: Yard-Man Страницы: 32

Бренд: P1 Страницы: 52

Бренд: Jacobsen Страницы: 58

Бренд: MTD Страницы: 2

Бренд: Land Pride Страницы: 58

Бренд: Tiger Страницы: 84

Four Wheel Steer Lawn Tractors

Бренд: Yard Machines Страницы: 16

Бренд: Baroness Страницы: 40

Бренд: ARNETOLI MOTOR Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды