Ferris 5900576 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 52

background image

12

www.ferrisindustries.com

Operator Safety

Safety Interlock System

This unit is equipped with safety interlock switches.
These safety systems are present for your safety,
do not attempt to bypass safety switches, and never
tamper with safety devices. Check their operation
regularly.

Operational SAFETY Checks

Test 1 — Engine should NOT crank if:

• PTO switch is engaged, OR

• Parking brake is not engaged, OR

• Motion control handles are not in the NEUTRAL

position.

Test 2 — Engine SHOULD crank if:

• PTO switch is NOT engaged, AND

• Parking brake is engaged, AND

• Motion control handles are locked in the

NEUTRAL position.

Test 3 — Engine should SHUT OFF if:

• Operator rises off seat with PTO engaged, OR

• Operator rises off seat with parking brake

disengaged.

• Operator moves motion control handles out of

their neutral positions before disengaging parking
brake.

Test 4 — Blade Brake Check

Mower blades and mower drive belt should come
to a complete stop within seven (7) seconds after
electric PTO switch is turned off (or operator rises off
seat). If mower drive belt does not stop within seven
(7) seconds, see your dealer.

NOTE: Once the engine has stopped, PTO switch
must be turned off, parking brake must be engaged,
and the motion control handles must be locked in the
NEUTRAL position after the operator returns to the
seat in order to start the engine.

WARNING

If the unit does not pass a safety test, do not
operate it. See your authorized dealer. Under
no circumstance should you attempt to defeat
the purpose of the safety interlock system.

USA Safety Icons

Alert

Toxic Fumes

Read the

Manual

Open Flame

Hazard

Fire Hazard

Amputation -

Rotating Parts

Amputation -

Hand In Blade

Amputation -
Foot In Blade

Thrown Objects

Hot Surface

Wear Protective

Gear

Pinch Point

Rollover Hazard

Overhead

Obstacles

Tipover

Dropoffs

Slippery Slopes

Keep Children

Away

Rollover

Hazard

Overhead

Obstacles

Not

for

Reproduction

«
...
12
13
14
15
16
...
»

Содержание 5900576





















































Отзывы:

Нет отзывов

Похожие инструкции для 5900576

Бренд: McCulloch Страницы: 36

Бренд: Parklander Страницы: 42

Бренд: elem Страницы: 99

Бренд: MTD Страницы: 28

Бренд: Snapper Страницы: 7

Бренд: New Holland Страницы: 52

Recycler 119-3320

Бренд: Toro Страницы: 4

Бренд: VITO GARDEN Страницы: 33

GF1800 ROPS Cab

Бренд: Kubota Страницы: 19

Бренд: Husqvarna Страницы: 3

Бренд: Parkside Страницы: 60

Бренд: McCulloch Страницы: 12

Бренд: McCulloch Страницы: 24

Бренд: McCulloch Страницы: 8

Бренд: McCulloch Страницы: 12

M40-110 CLASSIC

Бренд: McCulloch Страницы: 316

ECON HEDGEMASTER Mk3

Бренд: McConnel Страницы: 78

Бренд: Wheel Horse Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды