Ferris 5900576 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 52

background image

Operation

17

Zero-Turn Driving Practice

The lever controls of the Zero Turn rider are
responsive, and learning to gain a smooth and
efficient control of the rider’s forward, reverse, and
turning movements will take some practice.

Spending some time going through the maneuvers
shown and becoming familiar with how the unit
accelerates, travels, and steers — before you begin
mowing —is absolutely essential to getting the most
out of the Zero Turn rider.

Locate a smooth, flat area of your lawn

— one

with plenty of room to maneuver. (Clear the area
of objects, people and animals before you begin.)
Operate the unit at mid-throttle during this practice
session (ALWAYS operate at full throttle when
mowing), and turn slowly to prevent tire slippage and
damage to your lawn.

We suggest you begin with the Smooth Travel
procedure to the right, and then advance through the
forward, reverse, and turning maneuvers.

You must release the parking brake prior to moving
the control levers inward.

Forward Travel Practice

Gradually move both ground speed control levers
— evenly FORWARD from neutral. Slow down and
repeat.

NOTE: Straight forward travel takes practice. If
necessary, top speed can be balance-adjusted — see
the Speed Balancing Adjustment in the Adjustments
section near the back of this manual.

Reverse Travel Practice

LOOK DOWN & BEHIND, then gradually move both
ground speed control levers evenly BACK from
neutral. Slow down and repeat.

NOTE: Practice backing up for several minutes before
attempting to do so near objects. The rider turns
sharply in reverse as well as forward, and backing up
straight takes practice.

Figure 4. Forward Travel

Forward
Travel

Figure 5. Reverse Travel

Reverse
Travel

Smooth Travel

The lever controls of
the Zero Turn rider are
responsive.

The BEST method of
handling the ground
speed control levers
is in three steps — as
shown in Figure 3.

FIRST place your
hands onto the levers
as shown.

SECOND, to go
forward gradually push
the levers forward with
your palms.

THIRD, to speed
up move the levers
farther forward. To
slow down smoothly,
slowly move the levers
toward neutral.

Figure 3. Move Control
Levers Gradually

BASIC DRIVING

Not

for

Reproduction

«
...
17
18
19
20
21
...
»

Содержание 5900576





















































Отзывы:

Нет отзывов

Похожие инструкции для 5900576

Бренд: Sabo Страницы: 244

Бренд: Yard-Man Страницы: 11

Бренд: Flymo Страницы: 174

Бренд: elem Страницы: 99

Бренд: Rapid Страницы: 9

Бренд: Skil Страницы: 106

Бренд: Parkside Страницы: 50

Бренд: RedMax Страницы: 18

Бренд: MTD Страницы: 20

Бренд: Poulan Pro Страницы: 56

Бренд: Cobra Garden Machinery Страницы: 20

Бренд: Matrix Страницы: 68

Бренд: Worldlawn Страницы: 14

Бренд: Qualcast Страницы: 2

Бренд: Land Pride Страницы: 48

Бренд: California Trimmer Страницы: 8

Бренд: Tiger Страницы: 202

BOB-CAT 942311G

Бренд: Schiller Grounds Care Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды