background image

12

05

C

A

B

D

A.

Upper Hose Clamp

B.

Hose, 48” or 51” Long

C.

Lower Hose Clamp

D.

Hose Adapter

Figure 20. Install Hose

Install Hose

1. Before installing, the hose will need to be cut to

length.  Follow the chart below for the model/serial
number ranges and cut length.

NOTE:  When cutting the hose, it is necessary to cut
across the band of the hose.  The easiest method for
cutting the hose is to use a utility knife to cut the clear
section of the hose and use wire cutter or tin snips to cut
the band.  Before cutting, note the decal on the inside of
the hose noting the blower end.  CUT THE OPPOSITE
END.

2. Insert the hose (B, Figure 20) over the hose adapter

(D) on the bagger unit and overlap by at least two
bands.  Secure in place with the upper hose clamp
(A) as shown.

3. Insert the lower end of the hose over the blower

exhaust port and overlap by at least two bands.
Make sure the blower end decal is pointing towards
the blower exhaust port.  Make sure there is clear-
ance between the hose and drive tire.  It may be
necessary to loosen the upper clamp and twist the
hose to move the hose away from the tire.  Secure in
place with the lower hose clamp (C) by hand-tighten-
ing the knob.

4. Open grass bag cover and install grass bag frames

to support brackets.

5. Close grass bag cover and secure the rubber strap

to the hood latch.

6. Remove the valve stem covers and increase the rear

drive tire air pressure to 22 psi (151kPa).  Reinstall
the valve stem covers.

2-Bag Hood & Mount Installation

Model Number

Serial Number  Cut Length

1000ZKAV21/48

1500 & below

48”

1000ZKAV21/48

1501 & above

51”

1000ZKAV23/52

1045 & below

48”

1000ZKAV23/52

1046 & above

51”

1000ZKAV23/61

865 & below

48”

1000ZKAV23/61

866 & above

51”

1000ZK21/48

all

51”

1000ZK23/52

all

51”

1000ZK27/61

all

51”

IS1000ZKAV21/48

1905 & below

48”

IS1000ZKAV21/48

1906 & above

51”

IS1000ZKAV23/52

1400 & below

48”

IS1000ZKAV23/52

1401 & above

51”

ZT2148, ZT2148T, ZT2348T

all

51”

ZT2352, ZT2352T

all

51”

Содержание 46764



































Отзывы: