Ferris 46764 Скачать руководство пользователя страница 32

Страница: 32 / 34

Figure 42. Hole Location

Figure 43. Weight Rack Installation

Figure 44. Weight & Retainer Rod Installation

3/4”

(1,90cm)

1-1/4”

(3,18cm)

Install Weight Mount Rack

1. Measure and mark the front main frame tubes to the

dimensions shown in Figure 42.

2. Using a 3/8” drill bit, drill one (1) hole in each of the

main frame tubes from the outside surface of the
tube.

3. Slide the weight mount rack into the main frame

tubes and align with the holes drilled through the
frame (see Figure 43). It may require you drive the
arms into the frame tubes using a wooden block and
hammer.

4. Finish drilling through the opposite wall of the frame

tubes using the weight rack as a guide.

5. Install the 3/8” bolts and nuts and fasten securely.

6. Install the counter weights supplied with the grass

collector on the weight mount rack (see Figure 44).

7. Install the weight retainer rod through the weight

mount rack and secure with the hairpin clips (see
Figure 44).

Weight Mount Installation

(Ferris IS3000Z Series & Derby Stallion ZT2561 / 3-Bag System)

Содержание 46764



































Результаты поиска

Содержание 46764

Отзывы:

Похожие инструкции для 46764

Бренды по названию

Популярные бренды

Ferris 46764, Руководство оператора

Результаты поиска

Содержание 46764

Отзывы:

Похожие инструкции для 46764

Бренды по названию

Популярные бренды