manualshive.com logo in svg

Ferris 46764, Руководство оператора, Страница: 15 / 34

Поделиться
Скачать
Ferris 46764 Скачать руководство пользователя страница 15

9

00

61” Blower Mount & Drive Installation

Install Blower & Belt Guard

1. Loosen the 3/8-16 x 1” bolts (A, Figure 16) on the

blower brace.

1. Install the blower assembly onto the mount bar (B).

Push on the blower from the outside to obtain a tight
fit between the blower housing and mower deck.
Tighten the 3/8” x 1-1/4” bolts (C) that fasten the
mount bar to the mower deck.

2. Drill a 3/8” hole through the mount flange of the

blower mount bar and secure with a 3/8-16 x 1” bolt
(E) and 3/8-16 flange nut (D).

3. Adjust the blower brace until approximately

1/8” (3,1mm) clearance is obtained between the
brace and the chute mount bar.  Tighten the 3/8-16 x
1” bolts (A).

4. Install the 3/8” x 4” clevis pin (A, Figure 17) and hair

pin clip (C) as shown.

5. Install the plastic cap (B) in the end of the blower

mount bar.

6. Pull the idler arm lever against the spring to install

the drive belt on the spindle pulley.  The tension idler
should be approximately 3/4” - 1” (1,90 - 2,54cm)
away from the blower housing when belt in installed.
If not, remove the belt shield and drive belt from the
spindle pulley and reposition the top idler pulley in
the inside row of holes until the measurement is
achieved.

7. Reinstall the blower belt shield and secure with the

hardware previously removed (if necessary).

8. Install the deck belt shield (D) and secure with the

plastic knobs (E).

Figure 16. Install Blower

A.

3/8-16 x 1” Bolt

D.  3/8-16 Flange Nut

B.

Mount Bar

E.  3/8-16 x 1” Bolt

C.

3/8-16 X 1-1/4” Bolt

Figure 17. Install Belt Shield & Clevis Pin

A.

3/8” x 4” Clevis Pin

D.  Belt Shield

B.

Plastic Cap

E.  Plastic Knob

C.

Hair Pin Clip

B

D

E

A

C

D

E

B

C

A

Содержание 46764



































Отзывы:

Нет отзывов