Faulhaber MCDC2805 series Скачать руководство пользователя страница 45

Страница: 45 / 60

Appendix

Commands for Motion Control

Command Function

Description

Example

M *)

Initiate Motion

Activates positioning mode and starts positioning

Load Absolute Position

Loads new absolute position.

LA100000

Arguement: 1000 is one rotation.

Load Relative Postion

Loads a new relative position

LR5000

V *)

Select Velocity Mode

Activates velocity control mode and rotates

V2000

with the given value.

Get Velocity

Calls up command velocity

➔

500

Notify Position

Motor sends a “p” to the host terminal when the

NP10000

given position has been passed.

asynch

➔

No arguement: “p” is sent when target position is reached.

Notify Velocity

When the motor reaches the given velocity it

NV5000

transmits a “v” to the host.

asynch

➔

NPOFF

Notify Position Off

Deactivates a given Notify Position Command

NPOFF

that has not yet been carried out.

NVOFF

Notify Velocity Off

Deactivates a given Notify Velocity Command

NVOFF

that has not yet been carried out.

Commands for Velocity Control

Command Function

Description

Example

MV *)

Minimum Velocity

Sets the minimum speed in rpm

MV100

GMV

Get Minimum Velocity Calls up the minimum velocity on the host terminal

GMV

➔

MAV *)

Minimum Analog

Sets the minimum analog voltage

MAV500

Voltage

GMAV

Get Minimum

Calls up the minimum analog voltage on

GMAV

➔

Analog Voltage

the host terminal.

ADL *)

Analog Direction

The armature rotates left when positive voltage

ADL

Left

is applied at the analog input.

ADR *)

Analog Direction

The armature rotates right when positive voltage

ADR

Right

is applied at the analog input.

SOR *)

Source For Velocity

Chooses source for velocity.

SOR1

SOR 0:

Command velocity from RS-232 port

SOR 1:

Command velocity from a voltage
at the analog input.

SOR 2:

Command velocity with a PWM signal
at the analog input

SOR 3:

Command current limit value
at the analog input (command speed is given
with the V-command at the RS-232 port)

Содержание MCDC2805 series





























































Результаты поиска

Содержание MCDC2805 series

Отзывы:

Faulhaber MCDC2805 series, Инструкция по эксплуатации, Страница: 45 / 60

Результаты поиска

Содержание MCDC2805 series

Отзывы: