background image

Fastcorp, LLC 

DIVI Setup and Users Guide 

 

 Page 

18

 of 

62

                                                       Rev 6

 

Note - Store the block off plates in a safe place for future use. 

 

15.

 

FREEZER MAINTENANCE DIVI 

  

 

Viewing freezer temperature:  

  

While in Vend Mode (indicated by “Please Insert Money” on the scrolling marquee on the Digital Display), press 
the “*” key on the Customer Keypad. The current temperature will be displayed on the Digital Display.  

  

Temperature Adjustment: 

         Depending on the freezer model, some machines have adjustable temperature controllers. 

        

Standard Machines 

If available, the temperature may be adjusted by turning the Thermostat Dial located on the 
outside back of the freezer next to the left freezer lid hinge.  The scale ranges from 1 which is the 

warmest setting to 7 which is the coldest.  The recommended factory setting is “5”.  Three to four 

hours after powering up the Vendor, the temperature inside the Freezer should drop to about 

10°F / -23°C.  The operating temperature for the standard ice cream and   food vendor will vary 
based on the prevailing temperature at the machine.  Typically the operating range should be 
between -5°F/-20°C and -15°F/-26°C. 

Extreme Cold Machines 

Extreme cold machines should reach operating temperature approximately 4 hours after being 
turned on.  Typically, operating temperature ranges between -30 °F / -34°C and -40°F / -40°C. 
The temperature may be viewed by pressing the “*” key while in Vending Mode (Please Insert 
Money). 

 

Servicing the Freezer: 

 

The standard chest freezer inside the DIVI does not self-defrost. The freezer chest requires maintenance when ice begins to affect the 

vend cycle, product loading, or closing the freezer lid. The refrigeration system does not require any maintenance. Depending on the 
location’s moisture level (relative humidity) and frequency of operation, ice may accumulate inside the Freezer above the level of the 
bins. 

 

FASTCORP recommends keeping the plastic ice scraper (pr

ovided with the machine), and a 9” by 11” piece of 

cardboard or plastic inside the machine. Place the plastic under the area to be scraped to prevent the ice from 
falling into the bins. This entire process should only take a few minutes.  Wipe the area with a clean dry towel 
after the frost has been removed.  This process should be repeated each time the Vendor is serviced to prevent 
large scale ice buildup that will require a time consuming freezer defrost. 

 

Содержание DIVI































































Отзывы: