background image

Fastcorp, LLC 

DIVI Setup and Users Guide 

 

  Page 

1

 of 

62

                                                       Rev 6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 
 
 
 
 
Thank you for purchasing a FASTCORP DIVI merchandiser. This guide will cover safety information and setup of 
your machine for the first time. Please observe all of the safety precautions at the beginning of this manual. 
This machine represents over 2 years of product development and incorporates many technological advances 
offering you years of service without obsolescence. 
It is our sincere philosophy that we are partners with our customers and must grow together. With that in mind, 
we welcome all comments and suggestions either through your sales representative, our customer service 
department or whomever you have contact with from FASTCORP. 
Refer to this manual as you become a DIVI merchandiser in vending. 
 
Thank you, 

 

The FASTCORP Team 
 
 
 
 
 
 
 
 
 
 
 

 
The newest version of this manual may be downloaded at 

http://www.fastcorpvending.com/support

 or scan the QR code. 

Содержание DIVI































































Отзывы: