Faro FaroArm Fusion Скачать руководство пользователя | Manualshive

Страница: 108 / 130

background image

B-4

reasonable time of receipt of such notice, FARO shall have the System
and FaroArm diagnosed by its service personnel, and maintenance/
warranty service will be provided at no cost to the Purchaser if the
System and FaroArm is found by FARO to be defective within the
meaning of this Section.

(If, in the reasonable opinion of FARO after diagnosis of the system and
the FaroArm are not defective, the Purchaser shall pay the cost of
service, which shall be the amount that FARO would otherwise charge
for an evaluation under a non-warranty service evaluation.

4.06The Warranties do not apply to:

a) Any defects in any component of a System where, if in the
reasonable opinion of FARO, the FaroArm, Software or System has
been improperly stored, installed, operated, or maintained, or if
Purchaser has permitted unauthorized modifications, additions,
adjustments and/or repair to any hard drive structure or content, or
any other part of the System, or which might affect the System, or
defects caused or repairs required as a result of causes external to
FARO workmanship or the materials used by FARO. As used herein,
“unauthorized” means that which has not been approved and
permitted by FARO.

b) The Warranties shall not cover replacement of expendable items,
including, but not limited to, fuses, diskettes, printer paper, printer
ink, printing heads, disk cleaning materials, or similar items.

c) The Warranties shall not cover minor preventive and corrective
maintenance, including, but not limited to, replacement of fuses, disk
drive head cleaning, fan filter cleaning and system clock battery
replacement.

d) Any equipment or its components which was sold or transferred to
any party other than the original Purchaser without the expressed
written consent of FARO.

4.07Factory Repairs

a) IF SYSTEM IS UNDER MAINTANENCE/WARRANTY: The
Purchaser agrees to ship the Product to FARO in the original packing
containers. FARO will return the repaired or replacement Product.
FARO will incur the expense of the needed part and all return

08M46E00_FaroArmUSB.book Page 4 Tuesday, February 17, 2009 1:42 PM

«
...
106
107
108
109
110
...
»

Содержание FaroArm Fusion



































































































































Отзывы:

Нет отзывов

Похожие инструкции для FaroArm Fusion

Бренд: AccuMASTER Страницы: 2

Бренд: C-LOGIC Страницы: 4

Бренд: C-lock Страницы: 32

Бренд: C-LOGIC Страницы: 12

Бренд: Calsense Страницы: 4

Бренд: Datalogic Страницы: 6

Бренд: Datakom Страницы: 4

Бренд: Datakom Страницы: 38

Бренд: Oakton Страницы: 69

BLITZFIRE Series

Бренд: Task Force Tips Страницы: 20

Бренд: Hammond Страницы: 78

Бренд: GE Страницы: 35

Бренд: Yamaha Страницы: 24

Бренд: Hanna Instruments Страницы: 2

Бренд: Energic Plus Страницы: 12

Бренд: SKF Страницы: 12

Бренд: Avery Weigh-Tronix Страницы: 54

IMI Sensors Spindler 607A61

Бренд: PCB Piezotronics Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды