Faro FaroArm Fusion Скачать руководство пользователя | Manualshive

Страница: 50 / 130

background image

FaroArm

®

Manual

January 2009

42

Chapter 1: Introduction to the FaroArm

®

• Disable the R

ANGE

F

INDER

dialog box by clearing the Range Finder

On/Off check box.

• Select the S

HOW

V

ISIBLE

L

IGHT

check box to add all visible light to

the Preview window.

N

OTE

: Adding all visible light to the preview window will decrease

the number of frames per second sent to the computer and should only
be used when diagnosing problems with the FARO Laser Line Probe.

• Select the H

IGH

A

CCURACY

M

ODE

check box to operate the Laser

Line Probe in the High Accuracy mode. High Accuracy mode can
improve the performance of the Laser line probe by up to 30%, but
reduces your field of view by 1/2 and shortens your effective
maximum scanline width to 2/3 of the normal width.

Scan Rate and Density

Use the Scan Rate Density settings for data reduction. Reducing the
number of points the Laser Line Probe collects can improve system
performance, increase scanning speed and potentially reduce unwanted
noisy data.

• Scan Rate - choose the number of scan lines per second. 1/1 is the

normal rate of scan lines per second, set this to discard scan lines.

N

OTE

: Always set the scan rate to 1/1 when calibrating the Laser Line

Probe.

• Scan Density - choose the number of points on each scan line. 1/1 is

all of the points on the laser line, set this to discard points on each
line.

• Information - displays the unique information for the current FARO

Laser Line Probe.

Basic Settings

• From the M

ATERIAL

drop-down window choose any existing material

setting. Use the commands in this drop-down window to save
material settings.

N

OTE

: The current material setting is stored on your computer and in

the FaroArm. If you connect the FaroArm to another computer, the
current material will be

Unknown

. Save the material settings to copy

the settings from the FaroArm to the new computer.

• Click the AUTO button to set the Exposure and Noise Threshold

levels for the current material. Hold the Laser Line Probe in position,

08M46E00_FaroArmUSB.book Page 42 Tuesday, February 17, 2009 1:42 PM

«
...
48
49
50
51
52
...
»

Содержание FaroArm Fusion



































































































































Отзывы:

Нет отзывов

Похожие инструкции для FaroArm Fusion

BML SL1-ALZ-ZZ Series

Бренд: Balluff Страницы: 26

Бренд: Datalogic Страницы: 6

Бренд: Datakom Страницы: 4

Бренд: Datakom Страницы: 38

Network Card-MS

Бренд: Eaton Страницы: 26

Бренд: Hammond Organ Страницы: 25

Бренд: Hammond Organ Страницы: 87

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 12

Бренд: Motortech Страницы: 142

Бренд: Fluidwell Страницы: 48

Бренд: Hameg Страницы: 40

Бренд: SIGRIST Страницы: 84

Alyza IQ PO4-XYZ

Бренд: Xylem Страницы: 172

Бренд: PASCO Страницы: 13

Simple Precision OWD

Бренд: KAM Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды