FarmTek GrowSpan Gothic Pro 106314D страница 6 Скачать руководство пользователя

Страница: 6 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

H-CHANNEL INSTALLATION INSTRUCTIONS

The new H-channel design requires installation of the flat side facing out with channel side toward

the building. Some diagrams and photos in this document show installation of

original

H-channel with

channel side facing out. Design of new H-channel

does not allow

channel-side out installation.

Use the diagrams on this page to install H-channel with flat side facing out.

ATTENTION:

Use only 1-1/2" Tek screws to attach H-channel to building frame.

Do not use

shorter screws. They will not hold. Do not use washers on Tek screws when installing

H-channel.

ATTENTION:

Install all twin-wall poly carbonate panels with UV-protected side toward the sun.

UV-protected side

toward sun.

Install 1-1/2" Tek screws through

H-channel into building frame.

H-Channel

Center Groove

Flat side toward the sun.

Flat

Side

Channel

Содержание GrowSpan Gothic Pro 106314D






















































Результаты поиска

Содержание GrowSpan Gothic Pro 106314D

Отзывы:

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренды по названию

Популярные бренды

FarmTek GrowSpan Gothic Pro 106314D, Руководство по сборке

Результаты поиска

Содержание GrowSpan Gothic Pro 106314D

Отзывы:

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренды по названию

Популярные бренды