FarmTek GrowSpan Gothic Pro 106314D страница 23 Скачать руководство пользователя

Страница: 23 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

DOUBLE DOOR ASSEMBLY

The materials and parts needed to assemble the doors

include:
•  Door frames and polycarbonate panels
•  Door hinges and latch hardware
•  Aluminum U-Channel profile (#104213)
•  End cap profile (#104548)
•  Tek screws (#FA4482B & FA4484B))
•  Neo-bonded galvanized washers (#102921B)

ASSEMBLE AND ATTACH THE DOORS
NOTE:

Install the polycarbonate panels with the UV-

protected side to the outside.
1. Locate door frame (102923), assemble (if needed), and

place on a flat surface.

2. Select one polycarbonate panel (this will be one 4' x 8'

panel) and trim it so that the length is one-quarter inch

(1/4") shorter than the length of the door frame.

3. Trim width of panel (if needed) so that it is one-quarter

inch (1/4") narrower than width of door frame.

NOTE:

Trimming the panels as instructed will keep the

panel flush with the edge of the door frame after the

aluminum profile is installed.

4. Center the panel on the door frame.
5. Using the long Tek screws and neo-bonded galvanized

washers to attach the panel to the horizontal cross tube

of the door frame.

NOTE:

Attach the panel in the locations shown in the

photo to hold the panel in place while installing the

aluminum profile to the perimeter of the panel.

6. Install aluminum U-Channel profile to all edges of the

polycarbonate panel.

Photo shows the polycarbonate panel installed on

the outside of the door frame and finished with the

aluminum U-Channel profile. Corners are cut at 45°

angles.

To keep the panel and profile in place, the long Tek

screws and neo-bonded galvanized washers are

installed so the screw drills through the longer edge of

the U-profile (underside of the polycarbonate panel)

and the washer overlaps the shorter edge of the

U-profile (top) as shown above.

7. Repeat the above steps to attach the polycarbonate

panel and to install the aluminum profile to the

remaining door frame.

8. After assembling both doors, evenly space the hinges

along the door frame of each door and attach the

hinges to the assembled doors using the short Tek

screws.

Содержание GrowSpan Gothic Pro 106314D






















































Результаты поиска

Содержание GrowSpan Gothic Pro 106314D

Отзывы:

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренды по названию

Популярные бренды

FarmTek GrowSpan Gothic Pro 106314D, Руководство по сборке

Результаты поиска

Содержание GrowSpan Gothic Pro 106314D

Отзывы:

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренды по названию

Популярные бренды