FarmTek GrowSpan Gothic Pro 106314D Скачать руководство пользователя

Страница: 27 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

Attach main cover to Poly Latch U-Channel. Frame

shown above may differ from actual frame.

3. After tying the ropes to the main cover, throw the ropes

over the top of the greenhouse and pull the covers into

place.

Use ropes to pull cover over the greenhouse and onto

the frame. ADDITIONAL ASSISTANCE IS REQUIRED.

4. Center cover side-to-side and end-to-end.

IMPORTANT:

To prevent damage to the main cover

during installation, additional personnel and lifts may

be needed.

Verify that you have installed the IR film

according to the markings shown on the film.

5. Once the main cover is in place and centered, begin at

the peak of one end and install the wire spring into the

U-channel to secure the cover.

ATTENTION:

Center the main cover front to back and

side-to-side to ensure that enough cover material is

present to lock into the U-channel.

6. Remove the ropes as the covers are secured to the

greenhouse.

7. As the spring is install the spring into the U-channel

at the top of the first end rafter, ensure that an even

amount of the cover is exposed and maintained along

the edge of the greenhouse.

NOTE:

The cover material is cut longer/wider than

is required to cover the greenhouse. For easier

anchoring, allow approximately 10" to extend past the

edge of the end rafter as the cover is anchored into

place.

8. Continue down both edges of the first end rafter until

the entire length of the end of the main cover film is

secured in place.

9. Move to the other end of the building and repeat the

steps to secure the main cover in the U-channel.

10. After the cover is stretched end-to-end and secured

using the spring and U-channel, move to one side of

the greenhouse and repeat the steps to anchor the

cover film to the first side.

NOTE:

Begin at one end of the U-channel and work

toward the other. Another option is to begin at the

middle of each side and work towards each end.

Maintain an even length as working along the side. The

final stretching of the cover will take place when the

last side is secured.

Photos show installing the spring into the U-channel

on the outside of the greenhouse. The process is the

same for the U-channel attached to the top of the end

rafters.

INSTALL MAIN COVER (continued)

11. After securing the first side, move to the remaining

side, stretch the cover, and secure it in place.

NOTE:

Pull the cover tight as the spring is inserted into

the U-channel.

Содержание GrowSpan Gothic Pro 106314D






















































Результаты поиска

Содержание GrowSpan Gothic Pro 106314D

Отзывы:

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренды по названию

Популярные бренды

FarmTek GrowSpan Gothic Pro 106314D, Руководство по сборке

Результаты поиска

Содержание GrowSpan Gothic Pro 106314D

Отзывы:

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренды по названию

Популярные бренды