FarmTek GrowSpan Gothic Pro 106314D Скачать руководство пользователя

Страница: 21 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

END PANEL INSTALLATION (continued)

Mark UV Side

H-Channel

Installed End Panels

with H-Channel

NOTE:

When attaching any aluminum profile,

remember to account for the areas where different

sections of profile intersect so that the profile is cut to

the proper length.

Space the screws evenly at 16" when securing the

panels. DO NOT USE WASHERS WHEN SECURING

THE H-CHANNEL TO THE END WALL FRAMING.

The H-channel can be installed before the panel is

attached to the framing or after securing the panel to

the frame.

DO NOT install profile on the bottom of the end wall

panels.

These edges are sealed with the white vent

tape.

Always remove the protective film and mark and install the

UV-protected side to the outside of the greenhouse.

Secure all polycarbonat panels as shown in the diagrams

and photos below.

GLAZING PANEL

8MM POLYCARBONATE

PANEL SPLICE "H" CHANNEL

TEK SCREW

END WALL FRAME TUBE

TEK SCREW & NEO-BONDED WASHER

Use a Tek screw and washer to secure panel to end wall

frame. Do not crush panel when installing screws.

Diagram shows basic panel installation and fasteners used

to secure polycarbonte panels.

2. Apply white vent tape to the bottom of the lower panel

and then install the aluminum U-channel profile to the

edge of the panel adjacent to the door as shown on the

Polycarbonate Panels diagram.

3. Place the panel in position, attach it to the end wall

framing using Neo-bonded washers and the long Tek

screws.

Содержание GrowSpan Gothic Pro 106314D






















































Результаты поиска

Содержание GrowSpan Gothic Pro 106314D

Отзывы:

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренды по названию

Популярные бренды

FarmTek GrowSpan Gothic Pro 106314D, Руководство по сборке

Результаты поиска

Содержание GrowSpan Gothic Pro 106314D

Отзывы:

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренды по названию

Популярные бренды