FarmTek GrowSpan Gothic Pro 106314D Скачать руководство пользователя

Страница: 28 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

INSTALL MAIN COVER (continued)

12. Once the first cover is stretched and secure, install the

inflation fan kit in the desired location and according to

the instructions sent with the kit.

Install the Inflation Fan Kit

before

installing the second

main cover. Consult the instructions included with the

Inflation Fan Kit to install the kit.

13. After installing the inflation fan kit, repeat the steps to

install the film for the second main cover.

NOTE:

When installing the second cover film, use the

same U-channel used for the first cover film, and a

second run of spring, which is installed on top of the

first U-channel spring already in the channel.

14. With the second cover film layer installed, test the

operation of the inflation fan kit.

IMPORTANT:

If trimming the excess cover material at

the ends and sides, DO NOT remove too much of the

excess material. Some excess main cover material (the

material that extends beyond the end rafters) should

remain in place to more easily re-stretch the film if

needed.

15. Install drop-down curtain.

FRAME CHECK

Before you attach the drop-down curtain, inspect the frame

for sharp edges or fasteners that could damage the curtain

or kit components.
1.  Verify that all frame members are properly secured.
2.  Verify that all bolts and clamps are tight.
3.  Recheck the frame assembly for sharp edges or

clamps and bolts that may interfere with the installation

of the curtain. File or tape sharp edges as needed.

4. Reposition clamps and bolts as needed and tape all

rafter pipe joints with duct tape to protect the curtain.

5. Verify that the main building frame is properly and

adequately anchored.

Do not attach the drop-down curtain to an unanchored

frame.

6. Continue by reading the baseboard and ribbon board

information that follows.

Space below is reserved for customer notes.

Содержание GrowSpan Gothic Pro 106314D






















































Результаты поиска

Содержание GrowSpan Gothic Pro 106314D

Отзывы:

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренды по названию

Популярные бренды

FarmTek GrowSpan Gothic Pro 106314D, Руководство по сборке

Результаты поиска

Содержание GrowSpan Gothic Pro 106314D

Отзывы:

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренды по названию

Популярные бренды