FarmTek GrowSpan Gothic Pro 106314D страница 30 Скачать руководство пользователя | Manualshive

Страница: 30 / 53

background image

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

30

Revision date: 05.29.19

INSTALL THE DROP-DOWN CURTAIN

Locate these parts to attach the pulleys and drop-down

curtain axle:
• 131S075 (1.315 swaged pipe for axle) and 131P0XX

(where XX represents the length needed to complete

the axle assembly). The axle consists of the same pipe

as the purlins. See side profile for pipe identification if

needed.

•  106734 band clamp
•  103496 gearbox and 103544 mounting plate
•  102717 double drive
•  FA4482B Tek screws (for axle conduit)
•  FAH009B (1/4" x 4" carriage bolts)
•  FAH005B (1/4" x 2" carriage bolts)
•  FALF15B (1/4" lock nut) and FAME50B (1/4" flat

washer)

Continue with the steps that follow to install the drop-down

curtain components.

1. Take the 103544 mounting plate (shown above) and

move outside the end wall where you want to position

the gearbox.

2. Measure 12" to 24"

above the ribbon board

along the

end rafter, place the mounting plate against the end

wall, and align the plate mounting holes with the center

of the end rafter.

3. Mark plate mounting hole locations and drill the holes.

Use a 1/4" drill bit for the mounting holes.

103544 Mounting Plate (Figure 1)

Actual mounting plate may differ from what is shown

.

Gearbox Mounting

Holes

Axle Hole

Plate Mounting

Holes

NOTE:

Do not position the mounting plate in a location

where purlins, clamps, or other frame components will

interfere with the installation of the drop-down curtain

components.

The axle mounting clamps are installed

on the underside of the rafters inside the frame

.

4. Using the 1/4" x 4" carriage bolts and 1/4" nuts,

temporarily secure the 103544 plate to the outside of

the end wall.

5. With the plate in place, mark the location of the 2" axle

hole on the end wall polycarbonate panel, remove the

mounting plate, and cut the hole for the axle conduit.

NOTE

: If the end wall is covered with a fabric panel,

use a utility knife to cut a small X through the panel

within the 2" hole position and continue.

12"-24"

Center of End Rafter

Mark Plate

Mounting Holes

x

x

End Wall

(Panels have been

removed for clarity.)

Ribbon Board

mounted on the

outside of the

frame

x

2" Axle Hole

U-Channel

«
...
28
29
30
31
32
...
»

Содержание GrowSpan Gothic Pro 106314D






















































Отзывы:

Нет отзывов

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренд: Juliana Страницы: 38

CANOPIA LEAN TO 8x4 / 1.2x2.4

Бренд: Palram Страницы: 91

Бренд: LAMS Страницы: 30

Бренд: Palram Страницы: 110

Бренд: Hanover Страницы: 22

Бренд: ACD PRESTIGE Страницы: 53

Chili Pepper RW2277

Бренд: Royal Well Страницы: 2

Бренд: EINHELL Страницы: 12

Бренд: EINHELL Страницы: 32

Бренд: Palram Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды