FarmTek GrowSpan Gothic Pro 106314D Скачать руководство пользователя | Manualshive

Страница: 24 / 53

background image

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

24

Revision date: 05.29.19

DOUBLE DOOR ASSEMBLY (continued)

9. With the hinges attached to the doors, use the short

Tek screws to attach the doors to the frame of the end

wall.

a. Photo shows the end cap as attached to the door

frame tube. View shows the assembly from the

outside.

b. Cross section shows the end cap (dashed line)

attached to the inside/back of the door frame.

10. Install the 6" chain bolt to the upper part of the inside

of one door and the main latch assembly to the other

door.

Locations of door hinges may vary.

11. At the top and sides of the end wall door opening on

the inside of the frame, attach end cap and allow it to

extend below and into the door frame opening.

ATTENTION:

This profile acts as a stop for the double

doors, which prevents undo stress on the hinges.

Consult the photos that follow.

Inside

View

Outside

View

c. Dashed line identifies where to attach the end cap

profile. The end cap extends beyond the frame

members and into the rough opening to stop the

door in the frame and to help seal the gap between

the door and frame.

End cap used for

door stop and seal.

Diagram may show a different frame used for illustration

purposes only.

Door Frame

Tube

End Cap

(#104548)

«
...
22
23
24
25
26
...
»

Содержание GrowSpan Gothic Pro 106314D






















































Отзывы:

Нет отзывов

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренд: Robinsons Страницы: 44

Бренд: Palram Страницы: 8

Бренд: Outsunny Страницы: 7

Бренд: Outsunny Страницы: 17

Бренд: Vitavia Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды