FarmTek GrowSpan Gothic Pro 106314D Скачать руководство пользователя

Страница: 34 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

INSTALL THE DROP-DOWN CURTAIN (continued)
Install Curtain Conduit and Attach Rope

After installing all eye screws and pulleys, locate the curtain

panel, 1/2" conduit, 1/8" rope, FA4652 screws, and duct

tape. Refer to the parts list on the previous page if needed.

Complete these steps:
1. Unfold the curtain panel along one side of the shelter

and position the conduit pocket along the baseboard.

Dashed line shows where to position the pocket of the

curtain panel. Roof panels are not show for clarity.

2. Take one 8' section of the 1/2" curtain conduit (106816)

and insert the plain end (not the tapered end) into the

curtain pocket.

3. With the first conduit section in the pocket, add another

8' section to the first (plain end over tapered/swaged

end) and tape the conduit joint using duct tape.

4. Continue adding conduit sections and taping each joint

until the conduit is as long as the curtain panel.

5. Complete the curtain conduit installation by cutting

the conduit so that it extends from the panel pocket

approximately 1" at each end.

Tapered/Swaged End

6. Align the curtain and the installed curtain conduit with

the end rafters of the shelter.

7. Position the curtain conduit at the base of the

baseboard along the outside of the frame.

8. Measure the distance

from the curtain conduit up to

the axle conduit

mounted to the frame and add 12" to

ensure that the chord length is sufficient.

Diagram above shows where to measure to determine

cord length. Roof panels are not show for clarity.

Curtain Panel

Ribbon Board

Axle

Base Board

Panel Pocket

Curtain Conduit

Curtain Pocket

Curtain Panel

Axle

Base Board

Panel Pocket with Conduit

Measure this distance

Содержание GrowSpan Gothic Pro 106314D






















































Результаты поиска

Содержание GrowSpan Gothic Pro 106314D

Отзывы:

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренды по названию

Популярные бренды

FarmTek GrowSpan Gothic Pro 106314D, Руководство по сборке

Результаты поиска

Содержание GrowSpan Gothic Pro 106314D

Отзывы:

Похожие инструкции для GrowSpan Gothic Pro 106314D

Бренды по названию

Популярные бренды