FarmTek Growers Supply HydroCycle Lettuce Pro NFT Скачать руководство пользователя страница 28

Страница: 28 / 31

115141

Revision date: 01.14.21

Photo above shows a completed table as viewed from the drain end. Actual

position of clamps and channels may differ. Dashed line shows how to align

the channels for optimum growing.

Photo shows a side view of a completed system. Filter assembly, in-line

valve, reservoir, and air pump are also visible. Actual system differs in

size. Some components shown are not included in the micro NFT system.

Operation and assembly are similar. Photos are included to show overall

layout and an assembled system.

Larger system is shown as an example of a completed system.

ADDITIONAL PHOTOS

Photo shows the supply manifold and supply tubes of the NFT system.

Drain Manifold

Main Supply Line

Supply

Manifold

ATTENTION:

Reservoir and lid style shown

throughout this guide may vary. When needed,

critical dimensions are noted for hole locations.

Alternate channel

styles for best

growing results.

NOTE: Actual system

will have two supply

lines per channel.

Содержание Growers Supply HydroCycle Lettuce Pro NFT
































Результаты поиска

Содержание Growers Supply HydroCycle Lettuce Pro NFT

Отзывы:

Похожие инструкции для Growers Supply HydroCycle Lettuce Pro NFT

Бренды по названию

Популярные бренды

FarmTek Growers Supply HydroCycle Lettuce Pro NFT, Руководство пользователя

Результаты поиска

Содержание Growers Supply HydroCycle Lettuce Pro NFT

Отзывы:

Похожие инструкции для Growers Supply HydroCycle Lettuce Pro NFT

Бренды по названию

Популярные бренды