FarmTek Growers Supply HydroCycle Lettuce Pro NFT Скачать руководство пользователя страница 9

Страница: 9 / 31

Revision date: 01.14.21

115141

Assembly Instructions

1. Using the assembled frame as a bench, place one 5'

channel (115143) on cross supports.

2. Using 112509 adhesive, attach plain end cap (no

outlet–111127) to channel end that is resting on high side

of support table. This is the end with 36" legs. Be sure to

coat channel end with adhesive

before

you install end cap.

Repeat for all channels.

3. Move to other channel end and install the 111128 end cap

(with outlet). Coat channel end with adhesive

before

you

install end cap. Repeat for all channels.

4. Next, attach a 90° elbow (WF6682) to each 111128 end cap

as shown. Apply pvc primer and pvc cement (WF6990) to

the end cap outlet and to inside of fitting and slide fitting onto

outlet. Install fitting as shown with open end pointing down in

the 6:00 o'clock position.

ATTENTION:

Verify that you are using the WF6682 elbows.

These are without threads.

Do not use the WF6692 elbow.

ASSEMBLE ALL 5' 115143 CHANNELS

5. Once all end caps and drain elbows are in place, carefully

flip all channels over so bottom is facing up and open top is

down.

6. Apply 112509 adhesive along edges to secure end caps to

each 5' channel. Photos show an end cap with an outlet.

Secure plain end caps in same manner.

NOTE:

Be sure to coat all edges and seams of end caps to

prevent leaks.

7. Allow adhesive to dry before moving channels or testing the

system.

8. Continue with next procedure.

WF6682

Elbow

115143 Channel (5')

WF6682

Elbow

open

top-inside

channel

bottom

WF6990

PVC Cement

& 113372

Primer

Apply primer and cement in a well-ventilated area. Read and

follow container information for additional precautions.

Содержание Growers Supply HydroCycle Lettuce Pro NFT
































Результаты поиска

Содержание Growers Supply HydroCycle Lettuce Pro NFT

Отзывы:

Похожие инструкции для Growers Supply HydroCycle Lettuce Pro NFT

Бренды по названию

Популярные бренды

FarmTek Growers Supply HydroCycle Lettuce Pro NFT, Руководство пользователя

Результаты поиска

Содержание Growers Supply HydroCycle Lettuce Pro NFT

Отзывы:

Похожие инструкции для Growers Supply HydroCycle Lettuce Pro NFT

Бренды по названию

Популярные бренды