FarmTek Growers Supply HydroCycle Lettuce Pro NFT Скачать руководство пользователя страница 3

Страница: 3 / 31

Revision date: 01.14.21

115141

110725

Air Pump

109260 Air Stone

110722

Utility Pump

110091 Clear

Vinyl Tubing

111698 Ratchet Clamp

WR1095

Tape

Plastic Pipe & Tube Cutter

111128 (4)

End Cap w/ Outlet

111127 (4)

End Cap No Outlet

Important Information

PICTORIAL GUIDE

The following graphics and photos will help identify the different parts of the hydroponic system. (Some parts may not be shown.) To prevent mixing of fittings,

select only those that are needed for each procedure.

Keep all fittings in the shipping bags until they are needed.

10015106

Short Tee Fitting (12)

100442 (1)

Nut Setter

FA4470B (10)

Tek Screw

WF6990

PVC Cement

and

113372 Purple

Primer

PVC PRIMER & PVC CEMENT

Follow all directions printed

on pvc primer and cement

containers.

Purple color of

primer does not fade

! Use

caution during application

to reduce spills and over

application at joints.

Prime all joints before

assembly.

WF6504A

3/4" Black Hose

111046

1/4" White Polyethylene Tubing

Содержание Growers Supply HydroCycle Lettuce Pro NFT
































Результаты поиска

Содержание Growers Supply HydroCycle Lettuce Pro NFT

Отзывы:

Бренды по названию

Популярные бренды

FarmTek Growers Supply HydroCycle Lettuce Pro NFT, Руководство пользователя

Результаты поиска

Содержание Growers Supply HydroCycle Lettuce Pro NFT

Отзывы:

Бренды по названию

Популярные бренды