manualshive.com logo in svg

FarmTek Growers Supply HydroCycle Lettuce Pro NFT, Руководство пользователя

Поделиться
Скачать
FarmTek Growers Supply HydroCycle Lettuce Pro NFT Скачать руководство пользователя страница 12

12

12

115141  

Revision date: 01.14.21

Before assembly, dry fit all pvc connections before applying 

adhesive. Apply adhesive as instructed only.

Use photos to the right to attach drain manifold mounting hangers to frame 

using FA4470 Tek screws and 100442 driver.

5

Assembly Instructions

ATTACH DRAIN MANIFOLD HANGERS TO FRAME

112539 Hanger

100442 (1)

Nut Setter

FA4470 (10)

Tek Screw

ATTENTION:

 Install drain manifold at low end of frame, which has the 

shorter (33 1/2") leg pipes.

1"

A. Position bottom of hanger 

1" below bottom of tee fitting.

1/2"

B. Position bottom of hanger 

1/2" below bottom of tee fitting.

33 1/2" 

Legs

36" 

Legs

Attach 

hangers 

here

High End

Drain/Low End

Drain this direction

A

B

Attach Drain Manifold Mounting 

Clamps at the low end of the frame.

NOTE:

 Reverse clamp position if you want table to drain in the opposite 

direction.

Содержание Growers Supply HydroCycle Lettuce Pro NFT
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды