manualshive.com logo in svg

FarmTek Growers Supply HydroCycle Lettuce Pro NFT, Руководство пользователя

Поделиться
Скачать
FarmTek Growers Supply HydroCycle Lettuce Pro NFT Скачать руководство пользователя страница 22

22

22

115141  

Revision date: 01.14.21

Assembly Instructions

15

For optimal system performance and to extend the life of nutrient solution through increased 

oxygenation, an aerator pump and aerator stones are included. Position stones at reservoir 

bottom opposite water pump. 

Air pump must remain above nutrient level to prevent siphoning.

 

1.  Choose a position for the air pump and use it to determine the length of each air tube. Cut 

two air tubes of equal length using the 110091 tubing and tube cutter.  

 

ATTENTION:

 Position air pump at a level 

above nutrient level at all times to prevent 

siphoning

 of reservoir.

2.  Attach one stone to each line and set stones in reservoir. See photo for stone position 

opposite water pump.

3.  Place reservoir cover on reservoir and feed tubing up through access holes and connect 

free end of each tube to air pump.

ATTENTION:

 Always position the air pump 

above

 the nutrient level to 

prevent siphoning of the reservoir.

ATTACH AIR PUMP AND AERATOR STONES

Attach 110091 

tube to air stone.

109260 Air 

Stone

4.  Place air pump in position chosen in Step 1.
5.  Connect air pump to power and test operation. Verify air is filtering through each air stone. 

Monitor air pump regularly to ensure proper operation of aerator system. 

 

NOTE:

 When system is fully operational, air pump runs continuously. 

Do not connect air 

pump to any circuit controlled by a timer or shutoff switch.

6.  After testing air flow, turn off aerator pump until system is fully functional.

ATTENTION:

 Reservoir and lid style shown 

throughout this guide may vary. When needed, 

critical dimensions are noted for hole locations.

Содержание Growers Supply HydroCycle Lettuce Pro NFT
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды