manualshive.com logo in svg

FarmTek Growers Supply HydroCycle Lettuce Pro NFT, Руководство пользователя

Поделиться
Скачать
FarmTek Growers Supply HydroCycle Lettuce Pro NFT Скачать руководство пользователя страница 14

14

14

115141  

Revision date: 01.14.21

7

Assembly Instructions

DRILL HOLES IN RESERVOIR COVER

Drill the 2-1/2" Drain Tube Hole

1.  Determine in which corner you want to drill the drain 

tube hole. This is the corner directly under the tee 

fitting outlet of the drain manifold.

2.  Remove cover from reservoir and drill drain hole in 

the corner using a 2-1/2" hole saw. Do not drill cover 

over reservoir. Debris will damage pump and clog 

the filter.

Drill the 1" Supply Tube Hole

1.  Using a 1" hole saw, drill a hole for the 3/4" supply 

tube from the pump. Drill this hole at the edge of 

the porthole opposite the drain tube hole. See X's in 

upper-right photo. 

2.  Carefully remove cover material between porthole 

and 1" hole using a hand saw.

Drill the 5/16" Holes for the Air Pump Tubing

1.  Take a 5/16" drill bit and drill two holes 2" apart 

through cover. See photo below for location. 

ATTENTION:

 X marks hole locations based on reservoir 

design and position. 

Drill one 2-1/2" drain tube and one 

1" supply tube hole. Always space holes apart as shown. 

If 2-1/2" drain hole position is the other corner, drill the 1" 

supply tube hole on the opposite side of the porthole.

Move cover off reservoir. Place on support to 

drill the 2-1/2" drain hole.

2.  Remove all debris from cover and around all holes 

to prevent it from dropping into the reservoir when 

cover is set in place. 

Drill the 2-1/2" Drain Tube Hole

x

x

Actual cover may differ slightly from 

what is shown in this example.

Supply 

Tube Hole

2-1/2" Drain 

Tube Hole

Drill the 1" Supply Hole

Mark location.

Remove lip.

Drill 1" hole.

Remove debris.

ATTENTION:

 Reservoir and lid style shown 

throughout this guide may vary. When needed, 

critical dimensions are noted for hole locations.

3"- 4"

Содержание Growers Supply HydroCycle Lettuce Pro NFT
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды