manualshive.com logo in svg

FarmTek Growers Supply HydroCycle Lettuce Pro NFT, Руководство пользователя

Поделиться
Скачать
FarmTek Growers Supply HydroCycle Lettuce Pro NFT Скачать руководство пользователя страница 24

24

115141  

Revision date: 01.14.21

System Check

After assembling the 115141 NFT system, take a few minutes to check the 

system. Complete these steps.

1.  Verify all electrical cord ends are outside reservoir.
2.  Ensure supply tubes are fully inserted in channel lids.
3.  Fill reservoir with a few inches of water to cover pump.
4.  Verify that AC2804 in-line valve in main supply tube is open.
5.  Plug water and air pump power cords into an GFCI (Ground Fault Circuit 

Interrupter) outlet. Both pumps should turn on.

6.  Check each NFT channel to ensure water is running out each supply tube 

and drain end of each channel.

7.  Check all plumbing connections—main supply line and filter—for leaks.
8.  Check all pvc fittings for leaks. 
9.  Look for bubbles in reservoir to verify air is pumping to each air stone. 

Remember to always mount air pump on a surface above water level. 

Vibrations of pump can cause it to move. Make sure pump does not fall 

into reservoir or other liquids.

10. Once system has been checked and all adjustments are made, it is ready 

for use.

WARNING:

 KEEP ALL ELECTRICAL CORDS AND CONNECTIONS 

OUT OF THE RESERVOIR. CONSULT THE SERVICES OF A 

QUALIFIED ELECTRICIAN TO ADEQUATELY AND SAFELY 

CONNECT THE PUMPS TO A POWER SUPPLY. 

ALL ELECTRICAL CIRCUITS SHALL BE DESIGNED IN 

ACCORDANCE WITH LOCAL AND REGIONAL BUILDING CODES 

AND STANDARDS.

System Check

Column reserved for notes.

Содержание Growers Supply HydroCycle Lettuce Pro NFT
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды