3.
37
(MT13 - En 2015)
3
Ordering names (code 06)
You can list the names in alphabetical
order (from A to Z).
Move the jumper J1 from 2-3 to 1-2.
Enter the code 06; the first line of the
display shows “waiting” and the second
line shows a status bar; at the end of the
operation the push-button panel returns
automatically to the programming mode
(the display shows “Programming /
type:“ ).
Exit the programming mode by bringing
the jumper J1 back to 2-3.
How to enter the address of EC-EM
terminals (code 10)
Move the jumper J1 from 2-3 to 1-2.
Enter the code 10 and press
; the
display shows "ADDRESS EC".
Dial the number of the desired address
(255 for relay or camera activation mode;
250 for door lock mode; number of inter-
nal station before the first user of the
supplementary door lock service).
Press
to confirm.
Exit the programming mode by bringing
the jumper J1 back to 2-3.
Operations whit doorkeeper
exchangers (code 20)
Following settings are necessary if in the
system are installed main and/or
secondary door keeper exchangers.
For programming you must:
enter the code 20 and press the button
; on the first line of the display appears
the writing “Address PDX”, on the second
line is displayed the address saved
previously or empty spaces if no address
was stored previously;
delete all the addresses saved
previously by pressing the button and/
or enter the address 201 if the push-
button panel sends calls to 1 or more
main stations or the address 210 if the
push-button panel sends calls to 1 or
more secondary stations;
press the button
to confirm the setting;
to exit the programming mode, bring the
jumper J1 to position A.
Return to operation mode
Once you have completed programming,
bring the jumper J1 back to 2-3; the display
shows “ACI FARFISA / press < >” or the
text you have entered during programming
(see "Personalisation of display initial
text”).
EC-EM TERMINALS
The EC-EM terminals can be used to
connect:
-one active relay during the call and
for the entire conversation (default)
-one additional camera
-one additional door lock
To have these functions you must connect
the terminals correctly and make some
DOOR STATIONS
DIGITAL PUSH-BUTTON PANEL
1
2
3
4
5
6
7
8
9
3
2
5
5
2
3
Ø = 2,5mm
Personal
Computer
Continue by entering the code of a new
programming or exit by moving the
jumper J1 back to 2-3.
Loading names from PC (code 05)
You can load names directly from your PC.
Load the names on the PC using a
dedicated software application (software
supplied on demand).
Turn OFF the push-button panel and the
PC.
Connect the PC serial port to the stereo
jack on the back of the push-button panel
with a cable as shown in the figure.
programming operations on the TD2100MAS push-
button panel.
- Connection of one relay (see fig. 1)
Programming operations to be made:
- code 03 = set bit 6 at 0
- code 03 = set bit 7 at 0
- code 10 = enter address 255
- Connection of one additional camera
For this use you must connect the EC and EM terminals
to the corresponding terminals of the audio/video module
(see diagrams si51VM/32 and si51VM/169 on chapter
5).
Programming operations to be made:
- code 03 = set bit 6 at 1
- code 03 = set bit 7 at 0
- code 10 = enter address 255
- Connection of one additional door lock. For this
use you must connect a relay as shown in the figure and
program the push-button panel according to the desired
service. The presence of the additional door lock re-
quires to change the password (code 00). The first 8
passwords will activate the door lock connected to
terminals S1 and S2, and the remaining 8 passwords
will activate the door lock connected to terminals EC and
EM.
1) - activation of door lock from turn-ON button of
internal stations This function can be activated only
during a conversation with the external door station. In
idle state the buttons will activate the external door
station.
Programming operations to be made:
- code 03 = set bit 6 at 0
- code 03 = set bit 7 at 0 (3 seconds) or 1 (6 seconds)
- code 10 = enter address 250
2) - activation of door lock from button
of
internal stations
This programming allows for having two groups of users
connected to a single external door station, each of them
with its own door lock. The division between the two
groups is indicated by the number that is inserted in the
programming of code 10 (see page 3.37). You must
insert the last user number recognised by group 1 that
will activate the door lock connected to terminals S1 and
S2; all higher numbers will automatically be in group 2
and will activate the door lock connected to terminals EC
and EM.
Programming operations to be made:
- code 03 = set bit 6 at 0
- code 03 = set bit 7 at 0 (3 seconds) or 1 (6 seconds)
- code 10 = insert address of last user in group 1
(example: if you enter 99 you will have: group 1 with
codes from 1 to 99; group 2 from 100 to 200).
EM
EC
TD2100..
230V
127V
0
3
1
5
6
1471
2220
2220S
VD2120...
(fig.1)
TD2100MA
Move the jumpers J1, J2 and J3 on the
back of the push-button panel from 2-3
to 1-2.
Turn on the PC and then the push-button
panel.
Enter the code 05; the display shows
“TD2100MA > PC / in progress 0”.
Download the names from the PC within
15 seconds; the display shows
“TD2100MA < —> PC / in progress 1”,
“TD2100MA <—> PC / in progress 2”
and then the downloaded names.
At the end of download the push-button
deletes the existing names. The first line
of the display shows “waiting” and the
second line shows a status bar to show
the progress of the deletion operation.
At the end the display shows
“Programming / type: “ .
Turn off the push-button panel and then
the PC.
Disconnect the cable from the PC and
the push-button panel.
Bring the jumpers J1, J2 and J3 back to
2-3.
PC serial port
Stereo jack
