2.
48
(MT13 - En 2015)
Table 2.12. Addresses for the activation/deactivation of terminal
A1 functions
Address
Function transferring
To devices having:
000
call
the same user address
001÷200
call
another user address
211÷230
actuation
same programmed addressed
231÷254
door opening
same programmed addressed
255
not enable
-
- Secondary user address - By storing the user address of another
apartment it is possible to receive both the calls, talk to the external
station and actuate the lock of the external station calling (i.e.:
exchanger function, intercom installed in common area with multiple
users, etc.).
To program the secondary user address and it is necessary to:
enter the programming mode following the instructions described
in “Enter the programming phase”;
keep pressed the button "
" for more than 4 seconds; the
programming tone will be heard;
keep pressed the button "
" for more than 4 seconds; the
programming tone will be heard;
enter the 3 digit of the secondary user address (codes from 001
to 200) following the procedure reported on the paragraph “Entering
codes or addresses”;
press the button
to confirm; the acknowledge tone will be
heard;
proceed with another programming phase or exit the programming
phase by hanging up the handset.
- Internal secondary address - By programming the secondary
user address the internal address 000 is automatically encoded.
To change it, please proceed as follows:
enter the programming mode following the instructions described
in “Enter the programming phase”;
keep pressed the button "
" for more than 4 seconds; the
programming tone will be heard;
keep pressed the button "
" for more than 4 seconds; the
programming tone will be heard;
keep pressed the button "
" for more than 4 seconds; the
programming tone will be heard;
enter the 3 digit of the internal secondary address (codes from
000 to 007) following the procedure reported on the paragraph
“Entering codes or addresses”;
press the button
to confirm; the acknowledge tone will be
heard;
proceed with another programming phase or exit the programming
phase by hanging up the handset.
Programming the terminal A1
The following programming procedure enables sending the function
of terminal A1 (usually floor call) to other devices having the same user
address user (internal stations in parallel).
To program, you must:
enter the programming mode following the instructions described
in “Enter the programming phase”;
keep pressed the button "
" for more than 4 seconds; the
programming tone will be heard;
keep pressed the button "
" for more than 4 seconds; the
programming tone will be heard;
enter the 3 digits that make up the address of the desired function
(see table 2.12) following the procedure reported on the paragraph
“Entering codes or addresses”;
press the button
to confirm; the acknowledge tone will be heard;
proceed with another programming phase or exit the programming
phase by hanging up the handset.
Programming address to be stored to each button
The buttons
and
can be used to:
Intercom calls between intercoms (or video intercoms) located in the
same apartment (having the same user address), please refer to the
example “a” on this page. This function requires the buttons being
programmed with the internal address of the device to be called
(codes from 000 to 007) following the programming procedure “1”
described on page 2.49.
Intercom calls between users (with different user address), please
refer to the example “b” on this page. This function requires the button
being programmed with the user address to be called (codes from 001
to 200) following the programming procedure “2” described on page
2.49.
INTERNAL STATIONS
Programming examples
a) 3 intercoms in an apartment (users address: 100; internal addresses
in parentheses: 000, 001 and 002)
b) 3 intercommunicating users (users address: 100, 150 and 180)
c) 3 intercommunicating users, the first receiving the call addressed
to the second user (users address: 100, 150 and 180; internal
addresses in parentheses: 000 and 001).
Call floor
To have the floor call connect
the apparatus as illustrated
in the diagram.
GN
A1
Call floor
push-button
EX352
FP
100
(000)
150
180
100
180
100
150
150
(000)
180
(000)
Address button
Address button
User address
Internal address
Address button
Address button
User address
Internal address
100
(000)
(001)
(002)
(000)
(002)
(000)
(001)
100
(001)
100
(002)
S
ddress
econdary a
150 (001)
100
(000)
150
180
100
180
100
150
150
(000)
180
(000)
Address button
Address button
User address
Internal address
