manualshive.com logo in svg

Fagor ACSD series, Оригинальное руководство пользователя

Поделиться
Скачать
Fagor ACSD series Скачать руководство пользователя страница 4

ACSD-4/80

Digital Brushless 

AC S

ervo 

D

rive system - Ref.1609

DECLARATION OF CONFORMITY

Manufacturer:

Fagor Automation, S. Coop.
B.º San Andrés 19, C.P. 20500, Mondragón - Gipuzkoa - (SPAIN)

We hereby declare,

 under our responsibility that the product:

FAGOR AC BRUSHLESS SERVODRIVE SYSTEM

Parameter setting for the drive modules.

ACSD-05L, ACSD-10L, ACSD-20L, ACSD-30L 
ACSD-04H, ACSD-08H, ACSD-16H

and feed axis servo motors:

FXM1, FXM3, FXM5, FXM7, FKM2, FKM4, FKM6
Note.

 Some additional characters may follow the model references indicated above.

They all comply with the directives listed here. However, compliance may be verified
on the label of the unit itself.
mentioned on this declaration, meet the requirements on:

Safety

Electromagnetic Compatibility

In compliance with EC Directives 2014/35/UE on Low Voltage and 2014/30/UE on
Electrical Compatibility.

In Mondragón September 1st 2016

INTRODUCTION

FAGOR offers you a wide range of servo drive systems (AC Brushless motor + Digital
Drive) for applications requiring between 1.2 and 33.6 N·m at speeds between 1200
rev/min and 4000 rev/min for FXM motors and between 1.7 and 23.5 N·m at speeds
between 2000 rev/min and 6000 rev/min for FKM motors.
This manual describes the elements in detail and guides step by step through the
installation and setup of the drive system.
When installed for the first time, read the whole document.
Should you have any doubts or questions, please do not hesitate to contact our
technicians at any of our subsidiaries worldwide.
Thank you for choosing FAGOR.

EN 60204-1:2007 
CORR:2010 

Machinery safety. Electrical equipment of the machines.
Part 1: General requirements.

EN 61800-3:2004
/A1:2012

EMC directive on servo drive systems.

Содержание ACSD series



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды