manualshive.com logo in svg

Fagor ACSD series, Оригинальное руководство пользователя

Поделиться
Скачать
Fagor ACSD series Скачать руководство пользователя страница 34

ACSD-34/80

Digital Brushless 

AC S

ervo 

D

rive system - Ref.1609

About the connection

All the cables must be shielded, to reduce the interference on the control of the motor
due to the commutation of the PWM. The shield of the motor power cable must be
connected to the chassis screw at the bottom of the module and it, in turn, to mains
ground. 

Electrical connections

Power connection. Mains - Drive

The power supply of “ACSD-xxL” units must be three-phase 220 V AC, except in
modules ACSD-05L and ACSD-10L that can also be single-phase if parameter GP16
has been properly set. ACSD-xxH units must always be powered with three-phase 400
V AC. Parameter GP16 is ignored for these models.

F. 18

Installation of ACSD modules.

NOTE.

 Keep the signal cables away from the power cables.

INFORMATION. 

If ACSD-20L and ACSD-30L (220 V AC) units were powered

with single-phase voltage, the software would limit the current to 10 A.

INFORMATION. 

Do not power ACSD-xxH (400 V AC) units with single-phase

power voltage. The necessary bus voltage will never be reached. 

NOTE.

 The use of a transformer is not a must.

M6

M6

>50mm

>50mm

>10mm

>30mm

i

i

Содержание ACSD series



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды