manualshive.com logo in svg

Fagor ACSD series, Оригинальное руководство пользователя

Поделиться
Скачать
Fagor ACSD series Скачать руководство пользователя страница 36

ACSD-36/80

Digital Brushless 

AC S

ervo 

D

rive system - Ref.1609

Types of mains

Depending on the diagram of the electric energy distribution circuit, there are three
types of mains: TN, TT and IT. Depending on the type of mains, the cabling in the
electrical cabinet will vary considerably.
We here describe their characteristics and sample diagrams for a proper installation.

TN diagram

Distribution diagram that has a point directly connected to ground and the conductive
parts of the installation are connected to this point through ground protection conduc-
tors. This type of mains admits loads between one or several phases and the neuter.
There are three types of TN systems depending on the protection neuter and ground
combination:

TN-S diagram

 where the neuter and the ground protection conductors are separated

throughout the whole length of the system.

TN-C-S diagram

 where the neuter and the ground protection wire are combined in a

single conductor somewhere in the system.

TN-C diagram

 where the neuter and the ground protection functions are combined in

a single conductor throughout the system.

NOTE. 

A thermal switch may optionally replace the fuses.

NOTE.

 The secondary windings must have a star connection with its middle point con-

nected to ground.

NOTE.

 Note that the diagrams do not show the main contactor that must be connect-

ed between the transformer or auto-transformer and the ACSD unit!

WARNING.

 TN type mains are the only ones to which the ACSD system can

be  connected either directly or through an auto-transformer.

F. 21

TN diagram.

FACTORY LINE 

TRANSFORMER

DIFFERENTIAL 

BREAKER

MAINS 

FILTER

DIFFERENTIAL 

BREAKER

MAINS 

FILTER

DIFFERENTIAL 

BREAKER

MAINS 

FILTER

ACSD

ACSD

ACSD

L1
L2
L3

PEN

Содержание ACSD series



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды