![background image](http://html.mh-extra.com/html/faac/b680h/b680h_instruction-manual_535283045.webp)
17
ENGLISH
h 1
LOOP 1 holding time
Is used to set presence time on loop 1. When this time has elapsed, the board will self-
calibrate and signal “loop clear” (LED DL3 off). When the board is turned on, an automatic
reset is carried out.
Y
5 minutes
no
infinite
no
h2
LOOP 2 holding time
Is used to set presence time on loop 2. When this time has elapsed, the board will self-
calibrate and signal “loop clear” (LED DL4 off). When the board is turned on, an automatic
reset is carried out.
Y
5 minutes
no
infinite
no
H1
Loop 1 articulated lorry function
This function lets you increase the level of sensitivity at the time of detection, to allow correct
detection even in case of very tall vehicles or during the transit of a tractor and trailer.
Y
enabled
no
disabled
Y
H2
Loop 2 articulated lorry function
This function lets you increase the level of sensitivity at the time of detection, to allow correct
detection even in case of very tall vehicles or during the transit of a tractor and trailer.
Y
enabled
no
disabled
Y
t
Work time (time-out)
Maximum work time of the automated system before the motor stops, if the open or close
position is not reached. The value can be set from
O
to
59
sec. in one second steps. Next,
the display changes to minutes and tenths of a second (separated by a decimal point) and
time is adjusted in 10-second steps up to the maximum value of
4.1
minutes.
30
St
STATUS OF THE AUTOMATED SYSTEM:
Exit from programming, storage of data and automated system status display.
6.3
Pre-Defined Parameter Sets
The table below shows, for each set of pre-defined parameters, the
values that they will load in the board memory.
Basic Configuration
dF
0 1 0 2 0 3 0 4 0 5 0 6
At
01
02
03
04
05
06
bu
LO
E
E
E
E
E
E
PA
20
20
20
20
20
20
So
10
10
10
10
10
10
Sc
10
05
05
04
02
02
L 1
no
no
no
no
no
no
L2
no
no
no
no
no
no
S 1
05
05
05
05
05
05
S2
05
05
05
05
05
05
Advanced Configuration
The following table shows, for each set of pre-defined parameters,
the values that they will load in the board memory, in advanced
configuration.
dF
0 1 02 03 04 05 06
FO
25
25
30
28
30
40
FC
25
25
30
28
30
40
PF
no
no
no
no
no
no
tP
00
00
00
00
00
00
oc
35
35
38
32
32
32
FS
no
no
no
no
no
no
o 1
00
00
00
00
00
00
P 1
no
no
no
no
no
no
o2
03
03
03
03
03
03
P2
no
no
no
no
no
no
o3
0 1
0 1
0 1
0 1
0 1
0 1
P3
no
no
no
no
no
no
o4
02
02
02
02
02
02
P4
no
no
no
no
no
no
o5
01
01
01
01
01
01
AS
no
no
no
no
no
no
nc
00
00
00
00
00
00
nC
00
00
00
00
00
00
Содержание B680H
