EWM T5.00 Скачать руководство пользователя страница 66

Страница: 66 / 81

Functional characteristics

Machine configuration menu

099-00T500-EW501

2.9.2022

Display

Setting/selection

Pulsed TIG welding (thermal)

------- Function enabled (ex works)

------- For special applications only

Filler wire welding, operating mode

-------- Filler wire operation for automated applications,

wire is fed when current flows

-------- Non-latched operating mode (ex works)

-------- 3rd cycle operating mode

-------- Latched operating mode

TIG antistick

> see 5.2.7 chapter

-------- function active (factory setting).

------- function inactive.

Average value controller (AC)

-------- Function enabled (factory setting)

------- Function disabled

activArc voltage measuring

-------- Function enabled (ex works)

------- Function disabled

Fast take-over of control voltage (automation)

-------- Function enabled

------- Function disabled (ex works)

Welding procedure DC+ (TIG)

Protection against an accidental selection of polarity DC+ and the associated destruction

of the tungsten electrode (factory setting).

-------- Polarity switching to DC+ is possible.

------- Polarity switching is disabled (factory setting).

Gas monitoring

Depending on where the gas sensor is situated, the use of a pilot static tube and the

welding process monitoring phase.

------- Function disabled (ex works).

------- Monitoring during the welding process. Gas sensor between gas valve and

welding torch (with pilot static tube).

------- Monitoring prior to the welding process. Gas sensor between gas valve and

welding torch (without pilot static tube).

------- Permanent monitoring Gas sensor between gas cylinder and gas valve (with

pilot static tube).

Arc detection for welding helmets (TIG)

Modulated waviness for better arc detection

------- Function disabled

------- Medium intensity

------- High intensity

for AC welding machines only.

For machines with filler wire (AW) only.

only for machines with an interface for automated welding or appropriate automation components.

Содержание T5.00


















































































Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды

EWM T5.00, Руководство по эксплуатации

Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды