EWM T5.00 Скачать руководство пользователя страница 77

Страница: 77 / 81

Rectifying faults

Resetting welding parameters to the factory settings

099-00T500-EW501

2.9.2022

Error 57: Slave tacho error

Category B



Fault in the wire feeder (slave drive).



Check the connections (connectors, lines).



Permanent overload of the wire drive (slave drive).



Do not lay the liner in tight radii.



Check the liner for smooth movement.

Error 58: Short circuit

Category B



Short circuit in the welding circuit.



Eliminate the short circuit in the welding circuit.



Place the welding torch on an insulated surface.

Error 59: Incompatible machine



A machine connected to the system is not compatible.



Disconnect the incompatible machine from the system.

Error 60: Incompatible software



The software of a machine is not compatible.



Disconnect the incompatible machine from the system



Request service.

Error 61: Welding monitoring



The actual value of a welding parameter is outside the specified tolerance range.



Maintain the tolerance ranges.



Adjust the welding parameters.

Error 62: System component



The system component was not found.



Request service.

Error 63: Mains voltage error



Operating and mains voltage are incompatible.



Check or adjust the operating and mains voltage.

[1]

See technical data for values and other switching thresholds.

7.3 Resetting welding parameters to the factory settings

All customised welding parameters that are stored will be replaced by the factory settings.

To reset the welding parameters or machine settings to the factory settings, select parameter

in the

service menu

> see 5.11 chapter

7.4 Software version of the machine control

The query of the software versions only serves to inform the authorised service staff. It is available in the

machine configuration menu

> see 5.11 chapter

Содержание T5.00


















































































Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды

EWM T5.00, Руководство по эксплуатации

Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды