EWM T5.00 Скачать руководство пользователя страница 62

Страница: 62 / 81

Functional characteristics

Machine configuration menu

099-00T500-EW501

2.9.2022

Display

Setting/selection

Exit the menu

Exit

Switching the machine off and on

Required for applying various configuration parameters

Power source menu

Switch ignition mode

-------- HF ignition

------- Liftarc

HF intensity

------- Standard: Maximum value for the high-voltage ignition pulse Up

------- Reduced: Reduced value for the high-voltage ignition pulse Up

Re-ignition after arc interruption

> see 5.2.4.3 chapter

------- JOB-dependent time (ex works 5 s).

------- Function disabled or numerical value 0.1–5.0 s.

Reconditioning pulse (tungsten ball stability)

Cleaning effect of the tungsten ball at the end of welding.

-------- Function enabled (ex works)

------- Function disabled

TIG HF start (soft/hard) switching

-------- soft ignition (factory setting).

------- hard ignition.

Ignition pulse dynamics

-------- Function enabled (factory setting)

------- Function disabled

Minimum current limit (TIG)

> see 5.1.2 chapter

Depending on the set tungsten electrode diameter

------- Function disabled

-------- Function enabled (ex works)

Time-based power-saving mode

> see 5.7 chapter

Time to activation of the power-saving mode in case of inactivity.

Setting

= disabled or numerical value 5-60 min..

Cable resistance alignment

> see 5.2.13 chapter

Access control – access code

Setting: 000 to 999 (000 ex works)

Access control

> see 5.8 chapter

-------- Function enabled

------- Function disabled (ex works)

Operating mode menu

Program mode

------- Function disabled (factory setting)

-------- Function enabled

Program lock (P0)

The program P0 is locked when locking with the key switch. It is only possible to switch

between programs P1 to P15.

------- Function disabled (factory setting)

-------- Function enabled

Operating principle

------

synergic parameter setting (factory setting)

------

conventional parameter setting

Содержание T5.00


















































































Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды

EWM T5.00, Руководство по эксплуатации

Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды