EWM T5.00 Скачать руководство пользователя страница 49

Страница: 49 / 81

Functional characteristics

Welding programs

099-00T500-EW501

2.9.2022

5.2.11 RTF 1 foot-operated remote control

When the foot-operated remote control is connected, the machine switches automatically to non-

latched operation. The up- and down-slopes are switched off.

5.2.11.1 Start ramp

The start ramp function prevents an energy input that is too fast or too high immediately after the start of

welding when the user depresses the pedal of the remote control too fast and too far.

Example:

The user sets the main current at the welding machine to 200 A. The user presses the remote-control pe-

dal very quickly down by approx. 50% of the pedal travel.
• Start ramp is switched on: The welding current increases in a linear (slow ) ramp to approx. 100 A
• Start ramp is switched off: The welding current immediately jumps to approx. 100 A

The start ramp function is switched on or off with the parameter

in the machine configuration

> see 5.11 chapter

Figure 5-35

Display

Setting/selection

Start ramp

> see 5.2.11.1 chapter

-------- The welding current ramps up to the preset main current (factory setting)

------- The welding current jumps immediately to the preset main current

Gas pre-flow time

Start current (as percentage, dependent on main current)

End-crater current

Setting range in percent: depending on main current

Setting range, absolute: Imin to Imax.

Gas post-flow time

Содержание T5.00


















































































Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды

EWM T5.00, Руководство по эксплуатации

Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды