EWM T5.00 Скачать руководство пользователя страница 65

Страница: 65 / 81

Functional characteristics

Machine configuration menu

099-00T500-EW501

2.9.2022

Display

Setting/selection

Reset (to factory setting)

------- Disabled (ex works)

------- Reset the values in the machine configuration menu

------- Complete reset of all values and settings

Resetting is performed when exiting the menu (

Software version query

System bus ID and version number are separated by a dot.

Example: 07.0040 = 07 (system bus ID) 0.0.4.0 (version number)

Show warnings

> see 7.1 chapter

------- Function disabled (ex works)

-------- Function enabled

Fuse protection warning

------- Function disabled (factory setting)

-------- Function enabled

Dynamic power adjustment

> see 5.10 chapter

Automation menu

Automated/Manual (rC on/off) operating mode

Select machine/function control

------with external control voltages/signals

------with machine control

Operating mode switching via interface for automated welding

------- Non-latched

------- Special non-latched

Error output (relay)

Potential-free relay contact

------Relay contact for error message is open (factory setting)

------Relay contact for error message is closed

Setting for pulse pause current I2

The pulse pause current (I2) is set either relative or absolute to the main current (I1).

------Percentage setting (factory setting)

------Absolute setting

Function output

Potential-afflicted open-drain output that can emit various, adjustable signals through ac-

tive-low levels.

------- Switched off (factory setting)

------- Connection to AVC (Arc voltage control)

------- AC synchronisation or hot wire

------- Notification of a short circuit in the sensor voltage

Special parameters menu

Displaying and releasing the automation parameters

------- Function disabled (factory setting)

-------- Function enabled

Non-latched operation (version C)

> see 5.2.5.6 chapter

-------- Function enabled

------- Function disabled (ex works)

Welding current actual value display

> see 4.2 chapter

-------- Actual value display

-------- Nominal value display

Содержание T5.00


















































































Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды

EWM T5.00, Руководство по эксплуатации

Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды