EWM T5.00 Скачать руководство пользователя страница 60

Страница: 60 / 81

Functional characteristics

Power-saving mode (Standby)

099-00T500-EW501

2.9.2022

5.6.2 Reset welding task (JOB) to the factory setting

This function resets the JOB data of a welding task (JOB) to be selected to the factory settings.

Figure 5-53

5.7 Power-saving mode (Standby)

You can activate the power-saving mode by either pressing the push-button

> see 4 chapter

for a prolon-

ged time or by setting a parameter in the machine configuration menu (time-controlled power-saving

mode

)

> see 5.11 chapter

When power-saving mode is activated, the machine displays show the horizontal digit in the

centre of the display only.

Pressing any operating element (e.g. turning a rotary knob) deactivates power-saving mode and the ma-

chine is ready for welding again.

5.8 Access control

The machine control can be locked to secure it against unauthorised or unintentional adjustment. The

access block has the following effect:
• The parameters and their settings in the machine configuration menu, Expert menu and operation se-

quence can only be viewed but not changed.

• Welding procedure and welding current polarity cannot be changed.
The parameters for setting the access block are configured in the machine configuration

> see 5.11 chapter

Enabling access block

• Assign the access code for the access block: Select parameter

and select a number code (0–

999).

• Enable access block: Set parameter

to access block enabled

The access block activation is indicated by the "Access block active" signal light

> see 4 chapter

Disabling access block

• Enter the access code for the access block: Select parameter

and enter the previously selected

number code (0–999).

• Disable access block: Set parameter

to access block disabled

. The only way to disable the

access block is to enter the selected number code.

Содержание T5.00


















































































Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды

EWM T5.00, Руководство по эксплуатации

Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды