EWIKON HPS III Скачать руководство пользователя страница 71

Страница: 71 / 144

HPS-III-Nadelverschluss-Heißkanalsystem_Montage_BA_V-2-0_EN

Installation of HPS III valve gate hot runner systems

Pos. 1 Manifold

Pos. 5 Sprue bush

Pos. 6 Locating ring

Pos. 8 Drive unit integrated in clamping plate (version 2)

Pos. 17 Valve pin

Pos. 19 Synchronous plate

Pos. 20 Screw for valve pin holder

Pos. 21 Valve pin holder

Pos. 22 Overload safety device for valve pin

Pos. 23 Shoulder screw

Pos. 24 Guiding system (version 1)

Pos. 25 Guiding system (version 2)

(for restriceted installation space)

Pos. 50 Insulating plate

Pos. 51 Clamping plate

Pos. 53 Nozzle retainer frame plate

Pos. 54 Intermediate plate

Pos. 56 Contour plate

Installation of synchronous plate valve gate systems for HPS III-S nozzles

for standard and front installation

Read operating manual

In the installation process described in the following hazards for the
personal health are listed explicitly.

Furthermore, during installation the warning, safety and installation
notes for installation of EWIKON hot runner systems and compo-

nents as specified in chapter „5.2 General safety instructions“ must

be followed!

NOTE!

Dimensional check

Before installation the installation dimensions as listed in chapter
„5.4 Checks before installation“ must be checked and compared with
the values provided with the installation drawing.

Use approved standard parts only

Only standard parts which are approved for use in EWIKON hot
runner systems must be used. See chapter „5.3 Technical Requi-
rements“.

Screw connection for manifold

The screw connection for the manifold (pos. 13) is only required
when nozzles for standard installation are used.

When nozzles for

front installation are installed the manifold must not be screw
connected.

NOTE!

Содержание HPS III

















































































































































Результаты поиска

Содержание HPS III

Отзывы:

Бренды по названию

Популярные бренды

EWIKON HPS III, Руководство по эксплуатации

Результаты поиска

Содержание HPS III

Отзывы:

Бренды по названию

Популярные бренды