EWIKON HPS III Скачать руководство пользователя страница 135

Страница: 135 / 144

135

HPS-III-Heißkanalsystem_Servicehinweise_Außerbetriebnahme_BA_V-2-0_EN

Decommissioning

8.2 Instructions for disposal

NOTE!

Once disposed components must not be used again. EWIKON disclaims any responsibility for personal

injuries and material demage resulting from re-use.

In case that no special arrangements regarding return or disposal were agreed with EWIKON the disassembled

components have to be recycled after deinstallation:

•

Scrap metallic materials.

•

Recycle plastic components and plastic waste from the production.

•

Dispose the remaining components sorted by their material properties.

•

Electronic scrap and electronic components are special waste and must be disposed by authorised specia-

lised companies only.

•

With regard to the environmentally sound disposal of the deinstalled HPS III hot runner system the local

regulations for waste disposal must be observed.

Содержание HPS III

















































































































































Результаты поиска

Содержание HPS III

Отзывы:

Бренды по названию

Популярные бренды

EWIKON HPS III, Руководство по эксплуатации

Результаты поиска

Содержание HPS III

Отзывы:

Бренды по названию

Популярные бренды